Jump to content
SAU Community

Recommended Posts

Engine dead so turbo setup is for sale. Has done 20,000kms at 8psi, with the very occasional hit at 12-14psi (i can count the no. of times on one hand) and comes complete with:

- Trust TD06SH-20G 10cm^2 Turbo, rated at 420hp

- Trust Type R Wastegate

- Trust Stainless Steel Exhaust Manifold

Manifold and exhaust housing have been ceramic coated, and the compressor cover has been semi polished.

Comes complete with dump pipe and AFM pipe and oil lines. This turbo will bolt straight onto an RB20/25, with the exhaust plumbing up to your cat. Comes with re-written for R32 ECU for GTR injectors and Series II R33 AFM. Can supply GTR injectors and AFM at additional cost.

Need to sell urgently to get the car back on the road, but want to sell as complete kit

Asking $4,100 complete

(GTR injectors & AFM extra $400)

- Also have a std RB20 for sale, 170,000kms minimal blow by, suspected bent inlet valve. No reason to believe a problem exists with the engines bottom end.

Asking $300

Link to comment
https://www.sau.com.au/forums/topic/46728-trust-rb2025-td06-20g-setup/
Share on other sites

  • 2 weeks later...

Price Drop.... for $4150 you get:

- Trust TD06-20G , with ceramic coated exhaust housing (approx $1400)

- Trust Type R wastegate (approx $600)

- Trust stainless manifold, ceramic coated (approx $1300)

- Re-written Jap ECU for GTR Injectors and R33 AFM (approx $500)

- GTR injectors and F33 AFM (aaprox $500)

- Oil lines (approx $150)

- Dump pipe/front pipe (approx $300)

- Filter/AFM to turbo pipe (approx $150)

If you need a front mount i can also supply a HKS Type S cooler complete with clamps/silicon and 120deg bend straight off the throttle body to reduce pipe length/volume and also better clear the high mount turbo. Pipes/IC/BOV (SSQV Monza, 6wks old) for extra $1350

So for $5,500 you get a bolt on kit for an RB20DET that at 1.1 bar should se you around 210-220rwkws and at 1.3-1.4 bar around 230-250rwkws

R33 owners can offer prices for only the parts they want as obviously an R32 ECU etc isnt much good to you , but the manifold and dump etc will still definitely bolt on your RB25

Problem is if i sell just the manifold then im stuck with a turbo, wastegate and dump pipe that arent readily of use to anyone...so i would want very good money for it, ie not a reasonable figure...ready for it $1700.

Got any pics of this stuff??

This is the only photos i have until i go see the car next

td06front(1).JPG

The manifold is in top nic, so is the exhaust housing due to the black ceramic coating by Competition Coatings.

The wastegate has a nice soft spring so can run as little as 8psi if you require, or wind it in and run as much boost as you dare :) Wastegate is also in perfect working order.

Happto field ppls reasonabel offers for the turbo, manifold, wastegte and dump pipe

  • 3 weeks later...

Bump, had it dyno'd at 8psi the other day and it made 18?rwkws at 8psi. Didnt have time to do a full tune so left it very conservative tune to get the car back on the road. So to date the turbo still hasnt been stretched or even boosted

Can guarantee that this turbo setup makes an easy and lazy 210rwkws at only 11-12psi on a std RB20. Free to go for a drive in car with this setup, but will need to be quick as it will be removed from car soon

Roy, will Turbo bolt straight to std man?

Is WG on Dump or Exh Man?

Check PM - Greg.

  • 3 weeks later...

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now


  • Similar Content

  • Latest Posts

    • The average previous owner for these cars were basically S-chassis owners in the US. Teenagers or teenager-adjacent. I often tell people that neglect is easier to fix than something that was actively "repaired" by previous owners.
    • Update 3: Hi all It's been a while. Quite a lot of things happened in the meantime, among other things the car is (almost) back together and ready to be started again. Things that I fixed or changed: Full turbo removal, fitting back the OEM turbo oil hardlines. Had to do quite a bit of research and parts shopping to get every last piece that I need and make it work with the GT2860 turbos, but it does work and is not hard to do. Proves that the previous owner(s) just did not want to. While I was there I set the preload for the wastegates to 0,9bar to hopefully make it easier for the tuner to hit the 370hp I need for the legal inspections that will follow later on. Boost can always go up if necessary. Fitted a AN10 line from the catch can to the intake hose to make the catchcan and hopefully the cam covers a slight vacuum to have less restrictive oil returns from the head and not have mud build up as harshly in the lines and catch can. Removed the entire front interior just shy of the dashboard itself to clean up some of the absolutely horrendous wiring, (hopefully) fix the bumpy tacho and put in LED bulbs while I was there. Also put in bulbs where there was none before, like the airbag one. I also used that chance to remove the LED rpm gauge on the steering column, which was also wired in absolute horror show fashion. Moved the 4in1 Prosport gauge from sitting in front of the OEM oil pressure gauge to the center console vents, I used a 3D printed vent piece to hold that gauge there. The HKB steering wheel boss was likely on incorrectly as I sometimes noticed the indicator reset being uneven for left vs. right. In the meantime also installed an airbag delete resistor, as one should. Installed Cube Speed premium short shifter. Feels pretty nice, hope it'll work great too when I actually get to drive. Also put on a fancy Dragon Ball shift knob, cause why not. My buddy was kind enough to weld the rust hole in the back, it was basically rusted through in the lowermost corner of the passenger side trunk area where the wheel arch, trunk panel and rear quarter all meet. Obviously there is still a lot of crustiness in various areas but as long as it's not rusted out I'll just treat and isolate the corrosion and pretend it's not there. Also had to put down a new ground wire for the rear subframe as the original one was BARELY there. Probably a bit controversial depending on who you ask about this... but I ended up just covering the crack in the side of the engine block, the one above the oil feed, with JB Weld. I used a generous amount and roughed up the whole area with a Dremel before, so I hope this will hold the coolant where it should be for the foreseeable future. Did a cam cover gasket job as the half moons were a bit leaky, and there too one could see the people who worked on this car before me were absolute tools. The same half moons were probably used like 3 times without even cleaning the old RTV off. Dremeled out the inside of the flange where the turbine housing mates onto the exhaust manifolds so the diameter matches, as the OEM exhaust manifolds are even narrower than the turbine housings as we all know. Even if this doesn't do much, I had them out anyways, so can't harm. Ideally one would port-match both the turbo and the manifold to the gasket size but I really didn't feel up to disassembling the turbine housings. Wrapped turbo outlet dumps in heat wrap band. Will do the frontpipe again as well as now the oil leak which promted me to tear apart half the engine in the first place is hopefully fixed. Fitted an ATI super damper to get rid of the worn old harmonic balancer. Surely one of the easiest and most worth to do mods. But torquing that ARP bolt to spec was a bitch without being able to lock the flywheel. Did some minor adjustments in the ECU tables to change some things I didn't like, like the launch control that was ALWAYS active. Treated rusty spots and surface corrosion on places I could get to and on many spots under the car, not pretty or ideal but good enough for now. Removed the N1 rear spats and the carbon surrounding for the tailpipe to put them back on with new adhesive as the old one was lifting in many spots, not pretty. Took out the passenger rear lamp housing... what do you know. Amateur work screwed me again here as they were glued in hard and removing it took a lot of force, so I broke one of the housing bolts off. And when removing the adhesive from the chassis the paint came right off too. Thankfully all the damaged area won't be visible later, but whoever did the very limited bodywork on this car needs to have their limbs chopped off piece by piece.   Quite a list if I do say so myself, but a lot of time was spent just discovering new shit that is wrong with the car and finding a solution or parts to fix it. My last problem that I now have the headache of dealing with is that the exhaust studs on the turbo outlets are M10x1.25 threaded, but the previous owner already put on regular M10 nuts so the threads are... weird. I only found this out the hard way. So now I will just try if I can in any way fit the front pipe regardless, if not I'll have to redo the studs with the turbos installed. Lesson learned for the future: Redo ALL studs you put your hands on, especially if they are old and the previous owners were inept maniacs. Thanks for reading if you did, will update when the engine runs again. Hope nothing breaks or leaks and I can do a test drive.
    • No those pads are DBA too  but they have colors too. I look at the and imo the green "street" are the best.
    • I’m not sure what happened I told them about sonic tunes free OTS tune and the next the I know .. I was booted..   To funny 
×
×
  • Create New...