Jump to content
SAU Community

Recommended Posts

On 11/1/2016 at 1:30 PM, jhjones said:

No

Can you confirm if the little canister on the front is the same? Is that the receiver dryer? 

I've been offered a new model condenser and Amayama says they are interchangeable but the lines look different. 

 

14907719_1154543061267730_1004867670_o.jpg

Edited by ActionDan
Link to comment
https://www.sau.com.au/forums/topic/467514-r34-condenser/#findComment-7789517
Share on other sites

  • 3 weeks later...

Hey Dan, did you figure this out?  I'm actually trying to source one too...

From what I've found out, i think there's actually 3 models of condenser

Nengun list two - 

92110-AA002: Nissan - Skyline - R34 GTR - BNR34 (May/98-Jan/99) - A/C Condenser

92110-AA401: Nissan - Skyline - R34 GTR - BNR34 (Jan/99~) - A/C Condenser

I believe that there is also 92110-AA400 which is what Amayama says is interchangeable... but then RHD Japan also list the two different parts as:

Part Num: 92110-AA400 : 99/1 ~ 99/4
Part Num: 92110-AA401 : 99/4 ~ 

 

So, my problem is I'm pretty sure my car was a 99/4 produced car, so I'm really not sure exactly which one i need!  I've pulled the old one out and it looks like this

https://goo.gl/photos/a3TNQ7p2mgw8WFY59

 

I'm pretty close to just ordering one through RHDJapan - pity you're not in Sydney, maybe we could have got them shipped together!

Link to comment
https://www.sau.com.au/forums/topic/467514-r34-condenser/#findComment-7794205
Share on other sites

Get it through Amayama, they're cheaper.

I got one from Eribisu, Andrew Hawkins GTR.

It's a black one, mine was silver like yours and it went straight in.

They are all interchangeable it seems.

This condenser came with black lines from the core to the compressor and into the cabin, but they're identical to mine and a pain to swap unless you're already doing a turbo swap.

Link to comment
https://www.sau.com.au/forums/topic/467514-r34-condenser/#findComment-7794215
Share on other sites

  • 1 month later...
On 11/1/2016 at 9:07 AM, jhjones said:

theres two different part numbers for the GTR. Whats you chassis number?

92110-AA400- (9901-9904)

92110-AA401- (9904+)

My VIN is BNR34-004312 , Can you check for me as well?

Part No. A/C Condenser

Part No. Receiver-Driers

Link to comment
https://www.sau.com.au/forums/topic/467514-r34-condenser/#findComment-7804728
Share on other sites

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now


  • Similar Content

  • Latest Posts

    • Yeah I've had too many issues with knock off's on the BMW's. I don't want to do a job twice or more because the parts are shit.
    • I read this and thought "ah! I will do this scissor jack on the tow point thing!" I just use my floor/low profile/costco jack and lift the car up by the tow hook itself, then slide jack stands under. Never thought about using scissor into floor jack combo :p
    • Well, my new WMI system took much longer to finalize. I actually missed my dyno appointment last Friday and lost my 150$ deposit. I'll be going back in the next week or two.  To sum it up. I only kept the AEM tank from my old setup. I replaced the AEM pump with a higher flow/pressure ProMeth 30GPH pump. I also swapped over to a 6AN low pressure feed line to the pump from the tank. There's also a pressure switch you cannot see on the pump high pressure line.    This is feeding 6x 200CC direct port nozzles and 1x 500CC Pre Throttle body nozzle. All fittings are Swagelok, because well why not. I also have a 300PSI pressure sensor up front.    I now have my Haltech ECU controlling everything. I start my pump with a basic relay at 5PSI and deadhead it. I then PWM a 3000CC methanol Injector to control flow starting around 10psi. The pressure switch in the trunk, along with my tank level are safeties before I ever get to 10PSI, and then I use my pressure sensor upfront as a secondary safety to cut the WMI and corrections in case the injector blocks or a line ruptures.  Wish me luck on the dyno!    
    • So, I'm back with bad news. There's no jack long enough on this planet that will reach the front subframe. If by some chance there is, it would weigh 200lb's.  I purchased a long reach jack... The damn thing weighted 120lb's and was massive. Didn't even come close, was still short at least a foot. It was a pain, but I brought it back. Next I decided HA! No problem, I'll get an Extra long reach jack. Well, I couldn't lift the box... It must have weighed 160LB's and luckily there was an open box in store. I took measurement and was still nowhere close.  Sadly I've lost hope and have accepted defeat. 
    • Thanks for that tip, niZmO_Man. I think the battery is OK. It's quite a new one, but I'll check. Last time I needed a new battery, everything electronic was fine, except that there wasn't enough current to turn over the starter. I decided to order one of the partial AV system translation CDs from Car Audio Workshop in NZ. That might have some effect, or help me diagnose the date problem. 🤞
×
×
  • Create New...