Jump to content
SAU Community

Recommended Posts

Challenge Bathurst 2017

No firm date yet but it's on again late this year, anyone who wishes to join the Z Car Club Q Inc group and thereby secure garage accomodation can email a EOI to David [email protected] Basically this group is about old Datsuns with lot's of 240Z's and similar, importantly most of the drivers will have track experience, in 2016 it was pretty good with not much wankery going on. Up to you but you could do worse than hook up with our group.

  • Like 1
Link to comment
https://www.sau.com.au/forums/topic/468647-challenge-bathurst-2017/
Share on other sites

The group is nearly full, seriously, but lets have more Datsuns AKA Nissans to keep the BMWs and similar eurotrash out. So EOI David, he did a brilliant job in 2016, nothing in it for him, he just loves organising motor stuff.

  • 1 month later...

We have the dates, 16 to 19 Nov, sprints on Thu and Fri, regularity Sat and Sun. Entries will open July some time. Join our sensible driving Nissan/Datsun regularity group although we have allowed a couple of euros to slip in lol.

  • 1 month later...

FYI the Z Car Club Q block entry being organised by David email [email protected] will with a bit more support, which is well on track, be able to buy a block of entries. This means that the block run together in Regularity, plus have lock up 24 hour use of their allocated main pit garages with groups eg a SAU group, being able to share the one garage plus have camping advantages. But you have to go through David who is authorised by the organisers to accept entries, you may email him now with a EOI or for more info. 

Edited by 260DET
  • Like 1
  • 4 months later...

Ive entered in the sprint this year the V8 R32. 

Last year broke my diff 1st lap on saturday. Drove back to sydney and fitted a new one overnight. Sunday got black flagged every session in the regularity for going under 2.36 . My dash wasnt working correctly and had no idea of lap times. 

This year hope things go well. 

 

 

FB_IMG_1492775272997.jpg

  • 4 months later...
  • 1 month later...

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now


  • Similar Content

  • Latest Posts

    • I'm with you here. It's either loom has an issue, OR, injectors are not functioning properly. It could even be they're just constantly dribbling, hence the wet, but not firing.
    • Depending on how long the car sat it is very possible for injectors to be stuck open or closed, I'd get them cleaned and flow tested. Other than that, obviously when the loom changes and the car doesn't start any more....the loom is suspect so some tracing / comparing may be required
    • Harness is for a s1 Rb25det, and it is engine and lower harness.  the old harness had broken off plugs and was in very rough condition/exposed wires and splices etc. it is not able to be put back on the car, I could visually inspect to see if they had rewired any pins on the ecu plug. The fuel pump definitly isn’t turning off it’s an external pump and very loud you can hear it. Will look at the other harness tonight, am also going to pull the fuel rail and watch the injectors spray, will update here with what I find. Pretty sure at this point it has to be something to do with injectors because car will fire up on starting fluid and cas is clicking the Injectors. Fuel pressure is steady 43psi 
    • Check the injectors flow evenly, and are actually flowing what you and the ECU think they should be flowing. If it's starting up on starter fluid, you have a fuel issue. Is it possible under cranking your fuel pump is turning off?   The harness you replaced, is that the whole engine harness? Do yourself a test, and drop the old harness on and plug it into the Z32 ECU. It's possible they've wired things different. From memory S1 to S2 is different in RB25 and you may have a wrong loom
×
×
  • Create New...