Jump to content
SAU Community

r34 gtt coupe new panels

mutex
 Share

Recommended Posts

mutex Collaborator

mutex

Posted
Posted

r34 gtt coupe new panels

I bought some new panels from Nissan many years ago but never got around to using them.

They can be used to repair panel damage, rust, reinstating factory intercooler pipe holes, restoration, etc.

Part numbers:

driver rear quarter panel 78100-AA130 $700

pass rear quarter panel 78101-AA130 $700

driver rear inner guard wheel house out 76712-AA130 $300

pass rear inner guard wheel house out 76713-AA130 $300

driver hood ledge 64130-26U34 $300

pass hood ledge 64131-26U36 $300

driver boot pocket 74530-AA100 $200

pass boot pocket 74531-AA130 $200

Prices are negotiable, prefer pickup for rear qtr panels as they are large!

Thanks for looking.

Contact me either PM or 0402 427 004

All parts in Croydon Victoria.

Cheers,
Mark.

IMG_20170211_085456.jpg

IMG_20170211_085205.jpg

IMG_20170211_081945.jpg

IMG_20170211_081955.jpg

IMG_20170211_085308.jpg

IMG_20170211_085051.jpg

IMG_20170211_082241.jpg

IMG_20170211_082102.jpg

Link to comment
https://www.sau.com.au/forums/topic/469028-r34-gtt-coupe-new-panels/
Share on other sites
  • 3 years later...

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now
 Share
Go to topic listing


  • Similar Content

  • Latest Posts

    • Haggerty
      RB25DE NEO with Haltech ECU

      By Haggerty · Posted

      Yep, the closest base tune available was for the GTT, I went with that and made all the logical changes I could find to convert it to Naturally Aspirated. It will rev fine in Neutral to redline but it will be cutting nearly 50% fuel the whole way.  If I let it tune the fuel map to start with that much less fuel it wont run right and has a hard time applying corrections.  These 50% cuts are with a fuel map already about half of what the GTT tune had.  I was having a whole lot of bogging when applying any throttle but seem to have fixed that for no load situations with very aggressive transient throttle settings. I made the corrections to my injectors with data I found for them online, FBCJC100 flowing 306cc.  I'll have to look to see if I can find the Cam section. I have the Bosch 4.9 from Haltech. My manifold pressure when watching it live is always in -5.9 psi/inHg
    • brillo
      Leak from Tokico BM50 Brake Master Cylinder

      By brillo · Posted

      Hi My Tokico BM50 Brake master cylinder has a leak from the hole between the two outlets (M10x1) for brake pipes, I have attached a photo. Can anyone tell me what that hole is and what has failed to allow brake fluid to escape from it, I have looked on line and asked questions on UK forums but can not find the answer, if anyone can enlighten me I would be most grateful.
    • MBS206
      Cas issue

      By MBS206 · Posted

      It will be a software setting. I don't believe many on here ever used AEM. And they're now a discontinued product,that's really hard to find any easy answers on. If it were Link or Haltech, someone would be able to just send you a ECU file though.
    • nash47
      Cas issue

      By nash47 · Posted

      Yes sir am asking is there possible way from aem tuner from wiring pins 
    • MBS206
      Cas issue

      By MBS206 · Posted

      Have you checked cam to crank timing and confirmed balancer marks are correct?
×
×
  • Create New...