Jump to content
SAU Community

Recommended Posts

rb25det neo(from stagea) with r34 gtt ecu

hey guys i wonder if someone can help me out, i have few wiring problems a can solve myself.

- original car skyline r34 sedan rb20de neo

- swap rb25det neo ( aparrently neo from a stagea since it had 4wd oil sum, and does not have the traction control on the engine) I KEEP THE ORIGINAL LOOM FROM RB20DE NEO.

- first engine is working with r34 gtt ecu.

- engine works fine without the TCM/ABS module ( on r34) disconected but no speedometer

- engine cuts at 4000k when disconeccting the TCM/ABS module.

- i got and stagea ecu to solve the problem (stagea NO ABS or TC), engine pass 4000k normal, i connected the module TCM/ABS and now speedo works and all good, no cuts or etc,

problem i remove the ingnition key and the engine doesnt shut off whith stagea ecu, how can i solve this? please help

PS - my stagea ecu is 23710 0V300 and the first one is from a r34 gtt.

just for the record, my engine also cuts badly at 1 k or 2 k when i plug the ac dryer (3 cables) with either ecu.

ENGINE 3.jpg

ENGINE.jpg

motor.jpg

Its not the right ECU. The number you quote is for a S1 Stagea with the R33 engine. The Neo engine runs a Jecs ECU. The plug is different. You need to use the 34GTT ecu. BTW all Stageas have ABS. There is a fix on this site for if you have a warning light for the lack of Traction Control.

  • 2 weeks later...

Hey guys, so is it possible to put an rb25det neo out of a series 2 stagea into a r34 gt (non turbo)?

a) ill be using an r34gtt manual gearbox and a r34gtt ecu

b) Do the engine mounts line up the same?

c) can i use my r34 gt hicas power steering pump on a non hicas stagea engine?

d) can someone link the fix for the traction control fix?

Edited by Jet_Mapex
2 hours ago, Jet_Mapex said:

Hey guys, so is it possible to put an rb25det neo out of a series 2 stagea into a r34 gt (non turbo)?

Yes

a) ill be using an r34gtt manual gearbox and a r34gtt ecu

ok

b) Do the engine mounts line up the same?

dunno - probably big question is is it an awd or 2wd stagea

c) can i use my r34 gt hicas power steering pump on a non hicas stagea engine?

if it doesn't bolt straight up you should be able to adapt it

d) can someone link the fix for the traction control fix?

May be here:

http://www.skylinesaustralia.com/forums/topic/175032-power-fc-in-a-25t-rs-four-s/page__view__findpost__p__3208663

 

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now


  • Similar Content

  • Latest Posts

    • Manual boost controllers (where a little of the boost was bled off) were quite common back in the day, because they were cheap and easy. Generally they had a manual adjustment screw rather than being fixed like yours. Down side is they always bleed boost, not just when you want them to so an electronic boost controller that uses a solenoid will have less lag.
    • Hello , im new here and i have A31 home build  RB25det neo stock eng / turbo  aem ems 2 blue connector  aem 3.5 map aem cas disk aem wideband connected to ecu  355 lph pump 550 nismo yellow injectors side feed aftermarket regulator  and won’t start with base aem tuner basic tune eventually flipped cas 180 degree so it triggers on correct stroke not in exhaust cycle  Now it won’t start Wideband reads 10 and 11 at lowest fuel setting  and will share calibrations soon for aem tuner i think something is wrong in aem tuner    please if you have any information, am very grateful         
    • Legend. I ended up finding the facebook account of the owner of the first car i sent but sadly he deactivated the account. I think you’re right in saying it’s some sort of well done custom job. Really appreciate your help anyways.
    • Totally equivalent. Stock often goes from the comp cover because that's where the actuator is also installed and the factory needs 2" of hose to make the connection - and it comes as a pre-assembled unit. They totally have a boost reference from somewhere between the turbo and the throttle(s). Oh, jeez. Just do it in M12 then. We don't actually care that much. I would expect any such AN converter fitting to rely on an o-ring or some other seal onto a flat surface under the flange of the hex**, because bolt threads are no intended to provide a pressure seal. unlike..... pipe threads. **which also requires a suitably flat and smooth surface on the turbo's boss to provide the seal.
    • I also used NP   That’s were it’s seems to be the best place to fit it? All schematic shows also that it’s should be referenced from the turbo housing. But idk, I do see high hp cars without any connection or anything to their turbos, so I really don’t know how they connect their things
×
×
  • Create New...