Jump to content
SAU Community

FS, QLD- RB20s x3 and parts $150 the lot

AgentA31

By AgentA31,
in Classifieds

 Share

Recommended Posts

AgentA31 Apprentice

AgentA31

Posted
Posted

FS, QLD- RB20s x3 and parts $150 the lot

Item: Rb20det motors x3 and parts

Location: Gympie, QLD

Price: $150 ono, all in one lot.

Phone: 0432549745

Howdy, my cefiro is long gone and Ive still got a bunch of RB20det stuff sitting in my shed. Theres 3 motors total (no turbos) and a bunch of parts.

The 1st complete motor ran great but when tested it was a bit low on comp in 1 cyl so I swapped it out.

I believe the 2nd is fairly complete, was a spare so condition unknown.

the 3rd is in pieces, good for parts.

Id prefer to see this stuff go to someone who can use it, in the next week, otherwise its all going to the tip. I'll try to take a coupla pics tomorrow.

$150 THE LOT, one deal takes all, pickup only no post

 

Bring a trailer and some strong arms/ engine crane :) if I dont answer I may be out of reception, give me a text and Ill call back as soon as I can.

Jes

 Share
Go to topic listing


  • Similar Content

  • Latest Posts

    • EndZee
      R33 Gts/-t Abs Module Wiring Schematic (not Gt-r)

      By EndZee · Posted

      Brooooo Please send ABS control unit schematic Please! R33 gts25t ABS (Its two plug ecu, black and white) wire colors possible? [email protected]
    • GTSBoy
      Boost cut after swap(RB25DET NEO) R34

      By GTSBoy · Posted

      Don't even try to run it on the stock ECU if you're going to have the boost controller bring boost above ~10 psi. I've already told you that. If you use the Nistune ECU, you will need to CAREFULLY read the available documentation for Neo tuning, and read some threads on the Nistune forums, to discover the various things you have to do to prevent the ECU from going bananas when the boost is too high. The is a table associated with th boost sensor that must be modified to prevent it from shitting the bed. This is just one of the things that you will need to do to the tune in Nistune, because the Neo turbo ECU will be expecting to see a number of things (such as the TCS) that are not there, and you have to block the DTCs on those. It is totally not surprising to me that you are having the problems that you are, but the solutions to these problems have been known for >15 years. So just get it done.
    • dyl33
      VOLK RACING GTC CENTRE CAPS

      By dyl33 · Posted

      Centre caps $250
    • Kapr
      Boost cut after swap(RB25DET NEO) R34

      By Kapr · Posted

      Hi. Sry iam not a mechanic and iam not at the car atm so i dont know 100% but they told they measure those and even try to change those. AFM they have two. Coils are new a they have my old one too. Plugs too. ECU...we have 25 NEO stock and Nistune 25 NEO.   But i dont know if any one those could be the problem and why/if/what can cause this, Only thing they did not check is fuel...but that walbro 255 is new(like 1,5 years)... That fuel pressure gauge idk...but i let them know Any suggestions?   EDIT: how can they know if it is like you say he ECU pull power when it reaches a specific boost level that is too high? Tha car has boost controler
    • Duncan
      Boost cut after swap(RB25DET NEO) R34

      By Duncan · Posted

      Can you clarify what you mean by boost cut, do you mean it misfires both when under load (driving) and when stationary and out of gear? Or does the ECU pull power when it reaches a specific boost level that is too high (boost control issue)? Does it occur at idle with no throttle? When you say "the ECU is OK", what ECU is it and why do you think it is OK? Have you used the NEO ECU, and if so do you have a MAP sensor attached? Same for the AFM, why do you think it is OK? Do you have any way to put a fuel pressure gauge on it (even just a mechanical one between the fuel filter and fuel rail)?
×
×
  • Create New...