Jump to content
SAU Community

R33 Driver-side Seatbelt Problem

Ratty-Project-Daily-33gts
 Share

Recommended Posts

Ratty-Project-Daily-33gts Apprentice

Ratty-Project-Daily-33gts

Posted
Posted
R33 Driver-side Seatbelt Problem

Hey guys,

My drivers seatbelt wont retract or extend, could someone point me in the right direction to learning how to remove the panel behind the drivers seat. Do I have to remove the back seats to get to it?

Thanks,

Dyllan

Link to comment
https://www.sau.com.au/forums/topic/470672-r33-driver-side-seatbelt-problem/
Share on other sites
89CAL Grand Master

89CAL

Posted
Posted

Funny, i just plated with mine the other day
Mine just had some crap on it that was sticking when it passed through the seatbelt extender (or whatever you want to call it)
That panel is fairly easy to pull off. There is 1 screw somewhere in the middle and the rest is clips. Get a trim remover tool (super cheap sell a little kit of blue plastic ones) and pull the clips out to avoid damaging them. I took the bolt out of the top seatbelt carrier but cant remember if that was exactly necessary

So mine was only catching in the top, the retracting part was fine. Easy test for this is to grab the seatbelt below any of the parts it passes through and pull it to see how free it is. I cleaned my seatbelt with wax and grease remover then wiped it with some interior trim cleaner/shine

  • Like 1

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now
 Share
Go to topic listing


  • Similar Content

  • Latest Posts

    • timmy94
      boost source Size Garrett gt28 gen2

      By timmy94 · Posted

      Impossible to remove the housing while turbo is installed on the manifold on the engine. So I have to do it anyways. I plugged it so there will not be any debris in there. Will vacuum aswell 
    • JC71
      gtr hood match gt/gtt front fenders?

      By JC71 · Posted

      would a r34 gtr hood line up with gt/gtt stock fenders? after latch, front bumper and hinges are swapped for gtr ones? or would the fenders be too low or high in relation to the hood surface? ( I believe seeing somewhere that gtr front fenders use some type of riser for the sides, but do not know how that relates to stock gt/gtt fenders.)    
    • TurboTapin
      boost source Size Garrett gt28 gen2

      By TurboTapin · Posted

      You just need to remove the compressor housing, not the entire turbo. I would not be drilling and tapping anything with the housing still on anyways. 
    • Kinkstaah
      Mistakes were made, my R34 Story

      By Kinkstaah · Posted

      So, I put my boat on a boat. First of all, I'm going to come out and say it. Why is Tasmania not considered a holy goal, an apex that all road-legal modified cars go to, to experience? This place is an absolute wonderland of titanic proportions. If people are already getting club runs for once in a lifetime 30 person cruises to Tassy then I've never seemed to see it. It is like someone replaced the entire place with an idyllic wonderland for cars, and all of the people living there with paid actors who are kind, humble, and friendly. Dear god. After doing a lap of almost all of the place I've found that it's a great way to find out all of the little things that the car isn't doing quite right and a great way to figure it all out. All in all, I drove for 4 hours a day for a week and nothing broke. I didn't even need to open the engine bay. This is by all means a great success, but it has left me with a list of things to potentially address. I also now have a 3D printed wheel fitment tool which annoyingly hasn't got any threads in it to actually assemble it. I might be able to tape it together to check the sizing I actually want to use, but it'll likely involving pulling the shocks out to properly measure travel at least at the front, and probably raise the car while I'm at it, at least in the rear. I scraped on quite a few things and I'm not sure how else to go about it. I was taking anything with a bump at what felt like 89 degree angles. And address those 10 other tasks. And wash the car. God damn it is dirty. And somehow, the weather was perfect the entire time - And because I was on the top of Mt Wellington it turns out it was very much about to freeze up there. I did something I typically never do and took some photos up there in what must have been -10 and the foggy felt like suspended ice, rather than mere fog. If you own a car in Australia, you owe it to yourself to do it.
    • QB6SAGR
      Battle of the broken skylines

      By QB6SAGR · Posted

      Damn that was hilarious, and a bit embarrassing for skylines in general 😂 vintage car life ey. That R33 really stomped. Pretty entertaining stuff
×
×
  • Create New...