Jump to content
SAU Community

Recommended Posts

Thats a pic of standard injector seated in manifold.Screenshot_20180122-174707.thumb.png.068ceb99a81f538477dbc3e0d8547949.png

Do you think there would be any gains to try and make the injectors sit here compared to where they are sitting with the spacer installed which is approximately 8mm further out.

I would assume we could just drill the injector hole a little to let the spacer go further down.

When i get a chance ill have a go and see what happens lol

  • Like 1

I believe the 1550cc aka 1650cc (at 4bar) are more so a pencil stream injector so it wouldn't matter too much.

I've tried to look for spray pattern videos or photos but didn't find any solid evidence of the spray pattern.

In saying all this, I can safely say the 1550cc Bosch injectors actually run very well, dare say better than my old 875cc Siemen DEKA V (stainless shorties). However many variables such as an old tired motor, non NEO head and stock vs non stock parts.

Still same ECU.

  • Like 1

Johnny you have been talking about the 'jetski' injectors which I believe are the 930cc bosch units ending in 040 correct? You're well would these work on RB26 with the extended tips?

On 13/01/2018 at 5:07 PM, discopotato03 said:

Can we get you to measure the size of that water hole please

Cheers A . 

Does that top water passage have any requirement other than being a source point for other components?

  • 3 weeks later...
On 1/28/2018 at 7:33 PM, NEO25T said:

Does that top water passage have any requirement other than being a source point for other components?

On inspection, purely to cool the upper area of the manifold, provide water to the bleeder and the turbo.

You could go without feeding it any water and deleting the bleeder and sourcing the water elsewhere

36 minutes ago, Dose Pipe Sutututu said:

On inspection, purely to cool the upper area of the manifold, provide water to the bleeder and the turbo.

You could go without feeding it any water and deleting the bleeder and sourcing the water elsewhere

Ill have a better look at it later this week but im sure you can basically cut that top part off and just keep, how do i explain it, like 2 posts where the rail bolts down.

Then screw or weld dash fittings in to the water points you require as they will still be accessable.

Bit of stuffing around to fit injectors but for people that have nothing better to do it might be an option.

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now



  • Latest Posts

    • A bit late but A disk S13P fit over stock R32 GTR brakes, usually A disk front, O disk rear works.
    • Or, the height of the release bearing is not correct for your combo. Start with the bleeding and checking the slave moves throughout its range when you press the pedal (2 person required), but it is possible for the height to be internally wrong too (box back off to measure.
    • Yes, there's quite a few things that can go wrong during a clutch install. Very unlikely. I have a similar clutch. They (ACS) make good gear. No, it is not normal. It is possible that you just need to bleed the clutch slave. But the new clutch will also have a more aggressive actuation force/pressure, and so your old slave cylinder might be a bit leaky or otherwise compromised, and not up to the extra force required. Or the master cylinder, same.
    • Hi...so a "development" here aswell The swap is "done" and car went "test drive" BUT it seems the clutch(maybe gearbox?) is a little bit sad? I bought this clutch kit https://justjap.com/products/xtreme-heavy-duty-organic-clutch-flywheel-kit-nissan-skyline-r31-r32-r33-push-type "Problem" is that the first gear is hard to put into and it seems that the clutch is not disengaged. It was not the problem with the old clutch...(or like sometime the first gear would not get as easy specialy when the fluid was cold) So? Can it be like...bad "install" or is the clutch wrong ((it should not have been) i done research to get the right one) Or is this "normal" with new clutch and needs to be break in? 
    • @Duncan I can try  and thanks i did not thought about VIN and part numbers for 33/34. @GTSBoy yeah it looks like iam gonna do that  
×
×
  • Create New...