Jump to content
SAU Community

Recommended Posts

Hey guys, im new to skyline Australia and i would like some help.

My skyline r33 is losing power when i flat foot and the rpm reaches 5000rpm or so. Recently the problem has seem to evolve and make the car die out past 5000 rpm and what i mean is, the car is still on but there is no power what so ever past 5000. I've had this problem before except the dying out part and i fixed it with AFM. I have bought 2 AFM's and put them in the car and reset the ecu, however the problem is still there but the car dying out problem seem to be gone. Does anyone have any advice on what i can check next please. Im a student so i dont wanna go out and spend more money for nothing.

My car only has a few mods: (STOCK ECU + BOOST-no boost controller)

 

1.Spitfire coils packs

2.FMIC

3.After market fuel pump KEMSO 340LPH

4.Exhaust system turbo back

5. Iridium sparkplugs that i replaced about 6-8months ago. (Have not touched the gaping)

Tomorrow i will check the coils and spark plugs, but is there anything else i can check? Ive also checked previously for air leaks but found nothing.

Can timing belt be an issue? and o2 Sensor?

Thanks!

Rany

Link to comment
https://www.sau.com.au/forums/topic/474144-dying-at-5000rpm/
Share on other sites

Partially collapsed cat or muffler or flattened exhaust pipe can do that,  had a Falcon that started doing this at higher revs then one night on the freeway it fired a blazing ball of muffler packing out the tailpipe and became much louder.

14 hours ago, wildeagle44 said:

Maybe bypass the knock sensors? Could be pulling timing. 

Does it happen in every gear?

This time it is happening every gear. I cant flat foot on any gear from 1 to 4 so i'll check it out. would you know where their located?

Thanks mate

12 hours ago, BBGTR said:

Sounds like the igniter module, they sometimes break down at higher revs when they get old.

Thanks mate i'll have a look into it today.

The data sent from the car’s oxygen sensors to the computer helps it adjust the air-fuel mixture for optimal operation. If a sensor is bad or failing, the computer won’t be able to adjust this mix correctly. Also a clogged fuel filter can cause similar symptoms. Combine the two and you are in a world of pain. A new fuel filter is a cheap starting point buddy.

21 hours ago, Rusty Nuts said:

The data sent from the car’s oxygen sensors to the computer helps it adjust the air-fuel mixture for optimal operation. If a sensor is bad or failing, the computer won’t be able to adjust this mix correctly. Also a clogged fuel filter can cause similar symptoms. Combine the two and you are in a world of pain. A new fuel filter is a cheap starting point buddy.

Thanks for the reply Rusty. I have bought a new 02 sensor. Im gonna change it, if it fixes the problem im happy if it doesnt then i will just changed a part that is over 20 years old. I will also buy a new fuel filter since my 1 is still the original im sure.

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now


  • Latest Posts

    • Yep, the closest base tune available was for the GTT, I went with that and made all the logical changes I could find to convert it to Naturally Aspirated. It will rev fine in Neutral to redline but it will be cutting nearly 50% fuel the whole way.  If I let it tune the fuel map to start with that much less fuel it wont run right and has a hard time applying corrections.  These 50% cuts are with a fuel map already about half of what the GTT tune had.  I was having a whole lot of bogging when applying any throttle but seem to have fixed that for no load situations with very aggressive transient throttle settings. I made the corrections to my injectors with data I found for them online, FBCJC100 flowing 306cc.  I'll have to look to see if I can find the Cam section. I have the Bosch 4.9 from Haltech. My manifold pressure when watching it live is always in -5.9 psi/inHg
    • Hi My Tokico BM50 Brake master cylinder has a leak from the hole between the two outlets (M10x1) for brake pipes, I have attached a photo. Can anyone tell me what that hole is and what has failed to allow brake fluid to escape from it, I have looked on line and asked questions on UK forums but can not find the answer, if anyone can enlighten me I would be most grateful.
    • It will be a software setting. I don't believe many on here ever used AEM. And they're now a discontinued product,that's really hard to find any easy answers on. If it were Link or Haltech, someone would be able to just send you a ECU file though.
    • Yes sir am asking is there possible way from aem tuner from wiring pins 
    • Have you checked cam to crank timing and confirmed balancer marks are correct?
×
×
  • Create New...