Jump to content
SAU Community

Cooling system flushed 10x still dirty

MrStabby

By MrStabby,
in General Maintenance

 Share

Recommended Posts

MrStabby Grand Master

MrStabby

Posted
Posted

Since i installed a new radiator in the GTR i've been flushing the system with water as i'm changing coolant type. The green colour of the old coolant has gone, but the water comes out slightly dirty and with a very fine powder that settles out of the old coolant. The powder is too fine to feel. Should I persist with more flushes or is there something fundamental wrong?

KiwiRS4T Grand Master

KiwiRS4T

Posted
Posted

Depends how you have been flushing it. I have just been doing the same with someone else's car - i.e. draining and refilling the system and it is only slowly getting cleaner but a proper flush would require you to remove the thermostat and reverse flush the block with a hose.

MrStabby Grand Master

MrStabby

Posted
  • Author
Posted

I think the heater core control is stuffed - i can't get hot air, so no. But yeah i guess I should give that another go.

I have been bringing to car up to temp (according to the coolant sensor) but not running it long enough for oil temp to get to its normal level.

KiwiRS4T Grand Master

KiwiRS4T

Posted
Posted
2 hours ago, MrStabby said:

I think the heater core control is stuffed - i can't get hot air, so no. But yeah i guess I should give that another go.

I have been bringing to car up to temp (according to the coolant sensor) but not running it long enough for oil temp to get to its normal level.

So long as its hot enough to open the thermostat ...so I take it you are not flushing the block but just draining the radiator?

MrStabby Grand Master

MrStabby

Posted
  • Author
Posted
13 hours ago, KiwiRS4T said:

So long as its hot enough to open the thermostat ...so I take it you are not flushing the block but just draining the radiator?

I've been pulling off the bottom rad hose, and opening the bleeder on the top of the motor, and leaving to drain for an hour or so.

Should I pull off the drop radiator hose and run the garden hose through it too?

KiwiRS4T Grand Master

KiwiRS4T

Posted
Posted
3 hours ago, MrStabby said:

I've been pulling off the bottom rad hose, and opening the bleeder on the top of the motor, and leaving to drain for an hour or so.

Should I pull off the drop radiator hose and run the garden hose through it too?

To get a flow you have to also remove the thermostat so you could probably replace it while you are at it (with another stock one).

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now
 Share
Go to topic listing


  • Similar Content

  • Latest Posts

    • Jarsky
      R33 Fuel Pump & Brakes after alarm swap

      By Jarsky · Posted

      Thought I would get some advice from others on this situation.    Relevant info: R33 GTS25t Link G4x ECU Walbro 255LPH w/ OEM FP Relay (No relay mod) Scenario: I accidentally messed up my old AVS S5 (rev.1) at the start of the year and the cars been immobilised. Also the siren BBU has completely failed; so I decided to upgrade it.  I got a newer AVS S5 (rev.2?) installed on Friday. The guy removed the old one and its immobilisers. Tried to start it; the car cranks but doesnt start.  The new one was installed and all the alarm functions seem to be working as they should; still wouldn't start Went to bed; got up on Friday morning and decided to have a look into the no start problem. Found the car completely dead.  Charged the battery; plugged it back in and found the brake lights were stuck on.  Unplugging the brake pedal switch the lights turn off. Plug it back in and theyre stuck on again. I tested the switch (continuity test and resistance); all looks good (0-1kohm).  On talking to AVS; found its because of the rubber stopper on the brake pedal; sure enough the middle of it is missing so have ordered a new one. One of those wear items; which was confusing what was going on However when I try unplugging the STOP Light fuses (under the dash and under the hood) the brake light still stays on. Should those fuses not cut the brake light circuit?  I then checked the ECU; FP Speed Error.  Testing the pump again; I can hear the relay clicking every time I switch it to ON. I unplugged the pump and put the multimeter across the plug. No continuity; im seeing 0.6V (ECU signal?) and when it switches the relay I think its like 20mA or 200mA). Not seeing 12.4V / 7-9A. As far as I know; the Fuel Pump was wired through one of the immobiliser relays on the old alarm.  He pulled some thick gauged harness out with the old alarm wiring; which looks to me like it was to bridge connections into the immobilisers? Before it got immobilised it was running just fine.  Im at a loss to why the FP is getting no voltage; I thought maybe the FP was faulty (even though I havent even done 50km on the new pump) but no voltage at the harness plug.  Questions: Could it be he didnt reconnect the fuel pump when testing it after the old alarm removal (before installing the new alarm)?  Is this a case of bridging to the brake lights instead of the fuel pump circuit? It's a bit beyond me as I dont do a lot with electrical; so have tried my best to diagnose what I think seems to make sense.  Seeking advice if theres for sure an issue with the alarm install to get him back here; or if I do infact, need an auto electrician to diagnose it. 
    • Duncan
      After market rear camber arm adjustment

      By Duncan · Posted

      Then, shorten them by 1cm, drop the car back down and have a visual look (or even better, use a spirit level across the wheel to see if you have less camber than before. You still want something like 1.5 for road use. Alternatively, if you have adjustable rear ride height (I assume you do if you have extreme camber wear), raise the suspension back to standard height until you can get it all aligned properly. Finally, keep in mind that wear on the inside of the tyre can be for incorrect toe, not just camber
    • V35Newbie
      After market rear camber arm adjustment

      By V35Newbie · Posted

      I know I have to get a wheel alignment but until then I just need to bring the rear tyres in a bit they're wearing to the belt on the inside and brand new on the outside edge. I did shorten the arms a bit but got it wrong now after a few klms the Slip and VDC lights come on. I'd just like to get it to a point where I can drive for another week or two before getting an alignment. I've had to pay a lot of other stuff recently so doing it myself is my only option 
    • Duncan
      After market rear camber arm adjustment

      By Duncan · Posted

      You just need a wheel alignment after, so just set them to the same as current and drive to the shop. As there are 2 upper links it may also be worth adding adjustable upper front links at the same time; these reduce bump steer when you move the camber (note that setting those correctly takes a lot longer as you have to recheck the camber at each length of the toe arm, through a range of movement, so you could just ignore that unless the handling becomes unpredictable)
    • V35Newbie
      After market rear camber arm adjustment

      By V35Newbie · Posted

      I got adjustable after market rear camber arm to replace the stock one's because got sick of having to buy new rear tyres every few months. Can anyone please let me know what the best adjustment length would be. I don't have the old ones anymore to get measurements. I'm guessing the stock measurement minus a few mm would do it. Please any help on replacing them would be fantastic I've watched the YouTube clips but no-one talks about how long to set the camber arm to.
×
×
  • Create New...