Jump to content
SAU Community

Recommended Posts

Hi guys/gals,

PAS Westernsalon is looming near, and SAUWA is planning on making a big impact this year. This will be our 2nd year at the event and after great success and fun last year we're planning on doing it all again.

PAS will be held on the 30th and 31st of October, and this year it will be held in the new Convention Center on the Perth foreshore. This venue will be much improved over Belmont Racecourse, with alot more room and many more vehicles expected to enter.

We're looking for members who wish to enter there cars with the SAUWA display. Your car needs to in show-room condition, with something special to set it off from the crowd, either performance mods, wild bodykit, stereo etc. If you have a vehicle you want to enter then please contact me, either via PM, or email me at [email protected].

There are only limited spaces, and is only for paid SAUWA members or SAUWA sponsors ,so not everyone will be able to enter. The cost will be approximately $100 per vehicle, with SAUWA fundraising helping to fund the rest.

Even if you don't plan on entering a car, and just want to help out then we'll need all the help we can get.

Cheers

Paul

SAUWA President

Link to comment
https://www.sau.com.au/forums/topic/47452-pas-westernsalon/
Share on other sites

  • Replies 91
  • Created
  • Last Reply

Top Posters In This Topic

Think we've pretty much decided on a theme - we were jsut waiting on members feedback on it. I think we should keep the Theme talk etc to the "Members Only" section to keep away from prying eyes.

Link to comment
https://www.sau.com.au/forums/topic/47452-pas-westernsalon/#findComment-960694
Share on other sites

What can we do about models. As Paul knows I am able to source a couple of promo/models.. prob just 2... but if they go in the bikini comp do we still have to pay for full 2 days entry.... surely whats his face normally lets the models/bikini girls in for free or sumfin... plus do we have any spare SAU shirts lying around that they can wear.....

Link to comment
https://www.sau.com.au/forums/topic/47452-pas-westernsalon/#findComment-964158
Share on other sites

Dan .... im looking after the girls n costume side of things :P I'll be in touch with you shortly .... we are looking for four models all up ..... and i know EvlR33 approached paul too about it. So if you just want to forward any of the stuff etc to me on [email protected] that'll be cool.

Link to comment
https://www.sau.com.au/forums/topic/47452-pas-westernsalon/#findComment-964792
Share on other sites

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now



  • Latest Posts

    • Yep, the closest base tune available was for the GTT, I went with that and made all the logical changes I could find to convert it to Naturally Aspirated. It will rev fine in Neutral to redline but it will be cutting nearly 50% fuel the whole way.  If I let it tune the fuel map to start with that much less fuel it wont run right and has a hard time applying corrections.  These 50% cuts are with a fuel map already about half of what the GTT tune had.  I was having a whole lot of bogging when applying any throttle but seem to have fixed that for no load situations with very aggressive transient throttle settings. I made the corrections to my injectors with data I found for them online, FBCJC100 flowing 306cc.  I'll have to look to see if I can find the Cam section. I have the Bosch 4.9 from Haltech. My manifold pressure when watching it live is always in -5.9 psi/inHg
    • Hi My Tokico BM50 Brake master cylinder has a leak from the hole between the two outlets (M10x1) for brake pipes, I have attached a photo. Can anyone tell me what that hole is and what has failed to allow brake fluid to escape from it, I have looked on line and asked questions on UK forums but can not find the answer, if anyone can enlighten me I would be most grateful.
    • It will be a software setting. I don't believe many on here ever used AEM. And they're now a discontinued product,that's really hard to find any easy answers on. If it were Link or Haltech, someone would be able to just send you a ECU file though.
    • Yes sir am asking is there possible way from aem tuner from wiring pins 
    • Have you checked cam to crank timing and confirmed balancer marks are correct?
×
×
  • Create New...