Jump to content
SAU Community

Recommended Posts

All,

 

i am installing my walbro fuel pump this weekend. I understand the r34 gtt standard wiring uses a two stage fuel relay so on idle it cuts fuel or supply much less voltage (11v ) than 13.5 v.

 

my question is, i normally use a joint coupler with heat shrink covers. Is that ok inside a fuel pump? Obviously i will do the connection outsite of the fuel pump and then put it back in to the fuel pump.

 

i don’t think you can use electrical tape, can you ?

Link to comment
https://www.sau.com.au/forums/topic/475982-r34-walbro-255-fuel-pump/
Share on other sites

I'm maybe thinking more along the lines of a small I.D silicone fuel resistant hose (small motor fuel hose) line the exposed wiring/solder joint with something like https://www.supercheapauto.com.au/p/permatex-permatex-fuel-resistant-gasket-sealant-85420/356517.html and slip the silicone fuel resistant hose over it. the gasket sealant is non hardening so should keep even a slightly loose hose in place permanently as the sealant wont harden. Best I can come up with man hope it helps!

Thanks, will check it out

 

i am pretty worried on what happengs if positive and negative touch inside the fuel tank.

 

i think answer is spark and then boom. Have fine japaniese engeenering not thought of this?

 

even if fused, a small spark is enough to blow up the car with 60 liters of gas

 

re wire, i am thinking of soldering, what do you recon?

There can't be a boom in a sealed file tank even if the wires touch. No oxygen.

 

When I do pumps I offet the joints, so they can't touch and the use a piece of submersible fuel line over the positive joint. Like heat shrink but not shrunk.  None have exploded, so that's a pretty good result.

4 hours ago, drifter17a said:

If for whatever reason they do, screw coming loose?

 

lots of diy jumps simply use a wire connector so they could be setting up a death trap 

 

just amazed really on how stupied the design is

 

 

Too rich to ignite, even if you arched something inside the tank it won't ignite, even if created a physical spark it still won't ignite.

Engineers aren't stupid :)

 

8 hours ago, Dose Pipe Sutututu said:

Too rich to ignite, even if you arched something inside the tank it won't ignite, even if created a physical spark it still won't ignite.

Engineers aren't stupid :)

 

that is what I didn't know :)

 

well I was going mad getting all sort of sleeve to ensure they won't touch ...

5 hours ago, Ben C34 said:

If you don't believe us take off your petrol lid and drop a match in

will do later this evening, use my blow tourch .

 

i wonder why in the UK there is an old trick of calling the police and asking for a car to be removed which seems to have been abandoned by removing fuel cap and saying it is a fire hazard.

 

normally when the car is taxed( road tax) and MOT( mechanical check once a year) then they won't remove it but it if it annoying you people do above

 

14 hours ago, Ben C34 said:

If you don't believe us take off your petrol lid and drop a match in

Do not do this on a warm day, there will just enough fuel vapours and just enough air to ignite, just as the match goes down into the fuel neck lol

2 hours ago, Dose Pipe Sutututu said:

Do not do this on a warm day, there will just enough fuel vapours and just enough air to ignite, just as the match goes down into the fuel neck lol

Won’t go boom though.  Do it. 

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now


×
×
  • Create New...