Jump to content
SAU Community

Recommended Posts

All,

 

i am installing my walbro fuel pump this weekend. I understand the r34 gtt standard wiring uses a two stage fuel relay so on idle it cuts fuel or supply much less voltage (11v ) than 13.5 v.

 

my question is, i normally use a joint coupler with heat shrink covers. Is that ok inside a fuel pump? Obviously i will do the connection outsite of the fuel pump and then put it back in to the fuel pump.

 

i don’t think you can use electrical tape, can you ?

Link to comment
https://www.sau.com.au/forums/topic/475982-r34-walbro-255-fuel-pump/
Share on other sites

I'm maybe thinking more along the lines of a small I.D silicone fuel resistant hose (small motor fuel hose) line the exposed wiring/solder joint with something like https://www.supercheapauto.com.au/p/permatex-permatex-fuel-resistant-gasket-sealant-85420/356517.html and slip the silicone fuel resistant hose over it. the gasket sealant is non hardening so should keep even a slightly loose hose in place permanently as the sealant wont harden. Best I can come up with man hope it helps!

Thanks, will check it out

 

i am pretty worried on what happengs if positive and negative touch inside the fuel tank.

 

i think answer is spark and then boom. Have fine japaniese engeenering not thought of this?

 

even if fused, a small spark is enough to blow up the car with 60 liters of gas

 

re wire, i am thinking of soldering, what do you recon?

There can't be a boom in a sealed file tank even if the wires touch. No oxygen.

 

When I do pumps I offet the joints, so they can't touch and the use a piece of submersible fuel line over the positive joint. Like heat shrink but not shrunk.  None have exploded, so that's a pretty good result.

4 hours ago, drifter17a said:

If for whatever reason they do, screw coming loose?

 

lots of diy jumps simply use a wire connector so they could be setting up a death trap 

 

just amazed really on how stupied the design is

 

 

Too rich to ignite, even if you arched something inside the tank it won't ignite, even if created a physical spark it still won't ignite.

Engineers aren't stupid :)

 

8 hours ago, Dose Pipe Sutututu said:

Too rich to ignite, even if you arched something inside the tank it won't ignite, even if created a physical spark it still won't ignite.

Engineers aren't stupid :)

 

that is what I didn't know :)

 

well I was going mad getting all sort of sleeve to ensure they won't touch ...

5 hours ago, Ben C34 said:

If you don't believe us take off your petrol lid and drop a match in

will do later this evening, use my blow tourch .

 

i wonder why in the UK there is an old trick of calling the police and asking for a car to be removed which seems to have been abandoned by removing fuel cap and saying it is a fire hazard.

 

normally when the car is taxed( road tax) and MOT( mechanical check once a year) then they won't remove it but it if it annoying you people do above

 

14 hours ago, Ben C34 said:

If you don't believe us take off your petrol lid and drop a match in

Do not do this on a warm day, there will just enough fuel vapours and just enough air to ignite, just as the match goes down into the fuel neck lol

2 hours ago, Dose Pipe Sutututu said:

Do not do this on a warm day, there will just enough fuel vapours and just enough air to ignite, just as the match goes down into the fuel neck lol

Won’t go boom though.  Do it. 

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now


  • Similar Content

  • Latest Posts

    • Join SAU NSW for a flame-grilled feed & flame-spitting cruise! Sunday 17th August 2025 3:30PM Meeting Archies Flame Grille Sylvania Waters 4:45PM Cruise Departure 5:15PM Arrival at Cape Solander Kurnell Meet Location: Archies Flame Grille Final Destination: Cape Solander Kurnell *Disclaimer* There will be a lead and follow car so no one should get lost. If you would like to attend or bring others along please put your name down and a +1 as numbers will be needed prior! This is NOT a race and we will all be adhering to all road rules. If this is what you want please come to one of our many track days. This is an official SAU:NSW event and will be run under a CAMS permit. One of the things that really sets our club apart is our commitment to being true enthusiasts. When on normal roads we strive to maintain good relations with the authorities as well as the public in general. When attending one of Skylines Australia NSW events please try to: • Be aware of surrounding environment and act accordingly. • Drive courteously on the state’s roads as a true enthusiast should. • Understand how important it is to maintain the good name of SAU NSW and thus, treat others accordingly. • Any misbehavior will not be tolerated and you will be asked to leave.
    • Yeah good luck out there! Will be good to see a mighty GTST going harder than the GTRs
    • i will be there 😁
    • Hello!  i just finished manual swaping my r34 skyline with a r33 rb20de box(RB71C)box  When the car is running it squeaks crazy loud and it was smoking from the gearbox area. The gearbox is fine it was tested. The clutch slave cylinder seems like it doesn't fully releases the clutch. I want to ask if this noise is from the throw out bearing or could it be the clutch assembly or disk att.xFliq87Gzw6kImKBVqDebXkj0fBqymk0JaYeP3_3SlM.mp4
    • A few small updates since the previous post and lessons. I decided to do a little interior light upgrade on the 110. I quite like the iilumo items, even if they're a bit of a premium over other brands. You'll also note the Stedi Fogs, that will go into the S15 fog lights as I needed to match the bulbs since I got the new ones earlier. I hope they fit as the body is quite a bit longer than your normal bulb.  Annoyingly, I managed to trip the fuse, which normally wouldn't be an issue until I located the fuse. I can't say I've ever come across this. I had lucked out that someone nearby had a spare, but oddly enough Toyota dealerships seem to keep this in stock. I ordered some to keep in my stash and as luck would have it, someone else nearby tripped the same fuse so I passed on the favour.  I also did a little service on the 110 ahead of some additional work coming up. It's been annoying that Goleby's stopped carrying this particular HKS filter for the 110, so now I need to keep them on order from Japan. I also took the opportunity to install a bash plate and number plate riser. The plate riser is such a cheap but nice fix to help really tidy up the car. I'm tempted to now also replace my headlights, on this car. Both items were from Project Aero.    I also needed to replace the rear tyres on the 110, and after trying to get it aligned learnt that I need to replace some bushes in the front end, so that's next.  Closing out this update with a nicer picture as always! 
×
×
  • Create New...