Jump to content
SAU Community

Recommended Posts

So this is probably a weird one:

I have a V35 (350GT) 2005 - one of the dashboard back-lights, behind the odometer has died or has dimmed, the back-light for the dashboard clock only reliably works/comes on when the headlight sensors determine it's nighttime outside and dim the dashboard/gauge lights, my passenger side interior light only comes on sometimes when I open the doors AND the bloody fuel gauge doesn't work properly (sometimes it reads it's half-full and then suddenly as I drive it points to being full. Ohhhh and my vents will sometimes blow warm air, even when set to the lowest temp - other days it will be fine. (not because of the engine being warm or cold or it being a hot day etc)

Now I'm completely uninformed about the intricacies of cars, but i feel some, if not all, of these issues are connected because; as I drive to work, sometimes in the cold/damp mornings, my clock will be lit up and working and so will the fuel gauge. But a few hours later when I go to get food, back to square one! 

So I come here to ask for advice - I don't think it's a the actual fuel gauge itself because of how it all seems to happen together. Drawing on my radio technician background, it all feels like something to do with fuses or earthing issues, but I wanted to see what you guys think first.

Thanks

Link to comment
https://www.sau.com.au/forums/topic/477285-electrics-issuefuses/
Share on other sites

42 minutes ago, GTSBoy said:

Give all the likely fuses a wiggle. Pull 'em out put 'em back in. I have one circuit on my car (that powers the radio etc) that needs this every couple of years.

But I would warrant that it's more likely an earth problem.

Thanks so much for the reply. Can I ask, is there a particular place I look at to address an earth issue? 

Sadly, it would probably be behind/under the dash. You need to look at the wiring diagrams to see where there are earth points "close" to the instrument cluster and other devices in that area. Then you can pursue the wiring from those things back towards the various earth points on the steelwork behind/under the dash area.

Keep in mind that sometimes the earths are not actually where you might expect, and might, for example, be out near the sensing devices (like maybe the fuel sender). It is more likely that you will have dud earths out in the open/wet areas of the car or where f**kfisted previous owners could have done something stupid than behind the dash. But you can't exclude the possibility that someone has damaged something behind the dash either.

Edited by GTSBoy

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now


  • Similar Content

  • Latest Posts

    • Ahh...should have been clearer ~ there's 2 ... SMJ = super multi junction (connector)...   ...this is connector 6 & 25 in above image -- body harness to engine loom (6) & body harness to main loom (25) Headlights go to front via connector 6 ; fuel gauge goes to tank sender via connector 25  ...like I say this is R33 diagrams, but at a pinch R34 won't be too far different. *IF* the two ground faults are related, this can be the only place where both wires converge (as one runs to the back, the other to the front)... ....thing is, you probably need to establish if the faults are related (unless you examine that area and find obvious chaffing on the looms there to body ground)....*IF* the fuel gauge is still broken (full needle deflection), I'd be headed for the boot, remove fuel sender wire, key on and measure the voltage there ~ it should be roughly 10volts. If that's ok, check sender to ground resistance...if this is a dead short to ground (and there's fuel in it), then sender has failed or something funky has happened to wiring in the tank. edit: ahh...rereading the thread, this is R32....above fuel sender test still valid tho'
    • I just changed the timing belt on my RB25DET NEO and wanted to get some opinions. I’ve been super cautious, did a lot of research, and took my time. I’ve driven the car, and it runs fine. After warming it up, I revved it to 8000 RPM a few times—no issues, everything held up.   After the drive, I heard a noise that I think is either the clutch or possibly a tight accessory belt. It’s not constant, just comes and goes.   I took the timing cover off to double-check everything:   Belt is on properly, Tensioner is tight, Did the 90-degree twist test—belt isn’t too tight or too loose.     What still worries me is that I noticed the belt seems to sit a little toward the front edge of the gears, especially on the idler pulley. It even looks like it’s slightly coming off the edge there. Is that normal?   My old belt (5 years old, ~3,000 miles) also showed a bit of wear on that same edge, so maybe it’s just how it sits? I’m probably overthinking this, but since it’s my first time doing this on a NEO and the engine is forged, I really don’t want to mess anything up.   Also, I’m thinking of swapping to a clear front timing cover with the glass window. Would you recommend NITO or HPI? HPI looks reputable and their covers have 2.5mm thickness, but not sure if there’s a real difference between the two.   Any advice or reassurance would be much appreciated!
    • 40 grit sounds about right, to start. You make some decent cuts/damage in the coating with that, then rapdily scale up to maybe 80 and 120 for the bulk of the actual removal, then fine it off to 180 or 240 perhaps. No need to go any finer than that, and maybe no need to go even as fine as that. Wrap it on a big block and have at it. At least on the hub face.
    • Do the GKTech rear lower control arm mount relocation, and either alloy subframe inserts or very stiff subframe bushes. Traction is going to be at a premium!
    • Hello,   My name if Frederick, i'm 30 years old and I live in Belgium, Europe! I used to have a Nissan 370z daily but since I got a company car I turned that into my seattime driftcar. About 3 years ago I also wanted something older with more feel, so I got an R32 GTST with an rb26 engine. I am now getting the rb built to have around 800hp and it's close to being finished. I'm very excited for how it will drive and how driveable it will be! Regards, Fred!
×
×
  • Create New...