Jump to content
SAU Community

STAGEA RS260 TURBOS EXHAUST INTERCOOLER ect

TMLP
 Share

Recommended Posts

TMLP Community Regular

TMLP

Posted
Posted (edited)

I have a few parts to sell after upgrading my RB26 to s single turbo Maatouks MR700 build.

Twin turbos 7's still plumbed on the manifolds. APEXI 3" twin dump pipe & full stainless, 3" exhaust with (CAT??) mufflers & Dolphin tail pipe.

Intercooler & twin cold side pipes, all ran 300KW for 2 years and all only taken off for a RB30/26 build.

original MINES ECU 

 

Everything $3500.

IMG_3336.jpg

IMG_3337.jpg

IMG_3338.jpg

IMG_3339.jpg

IMG_3340.jpg

IMG_3341.jpg

IMG_3342.jpg

IMG_3343.jpg

IMG_3344.jpg

Edited by TMLP
added turbo size
TMLP Community Regular

TMLP

Posted
  • Author
Posted
1 hour ago, 260RedigoloS said:

I have a 260 RS , can I ask how much for the MR 700 build, thanks  ?

mine was 50K but depends on your specs I got the big bottom end & head package. 

 

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now
 Share
Go to topic listing


  • Similar Content

  • Latest Posts

    • djr81
      R32 update from 1990's spec.

      By djr81 · Posted

      So for the wide band is a Bosch 4.9 correct for the Link G4+ along with a Can bus? Just get the Link gear or is generic ok too? Eg here: LINK LINK DIGITAL WIDEBAND CAN MODULE WITH BOSCH 4.9 SENSOR : KYP Performance House  
    • djr81
      RB26DETT Sketchy boost mod?

      By djr81 · Posted

      Bit difficult to follow. Have a look below and see what the standard R32 layout was like. Note there was a restrictor in place immediately before "turbocharged pressure control solenoid" that, if removed, magically got you 1 bar boost.
    • ARB26
      RB26DETT Sketchy boost mod?

      By ARB26 · Posted

      I might be way off the mark here.. there must be a T junction under the manifold. That takes manifold pressure through a check valve prior to the T, one side splits out to this bleed off orifice, the other straight to the wastegate actuators. 
    • ARB26
      RB26DETT Sketchy boost mod?

      By ARB26 · Posted

    • ARB26
      RB26DETT Sketchy boost mod?

      By ARB26 · Posted

      Carrying out some engine due diligence before my first drive in a 260RS that has been in storage for 10+ years, and found two lines that are susposed to be plumbed into the boost control solenoid. One of the lines (the wastegate boost supply line) to actuate the gates, had a bolt in one end blocking it. The other line (main boost signal line) from the very rear of the intake manifold (RB26DETT) and runs up to the boost controller had this pill in the end of it as seen in photos. Other than the obvious (T28 Ceramic turbos might well be cooked)  Can anyone shed any light on if there is any validity at all with this mod, bleeding a constant fixed rate of manifold boost pressure off through this 3mm hole?  Is it deliberate?  Was this a 90s Jap mod done to RB26's? Or has someone just fitted this without any idea of what happens to ceramic T28s if they are not gate controlled?    
×
×
  • Create New...