Jump to content
SAU Community

2012 Rogue Problem - No RPM increase in drive/reverse/neutral when gas pedal is pushed, fine in park.


Recommended Posts

I start the car. Push the brake, shift to drive. Push the pedal. It goes forward slightly but then goes back to idle rpm. Flooring the pedal lets me get to ~1500rpm, maybe 2k if I trick it into it, but never move forward again.

Same happens for reverse. It even happens if I start it in neutral and just try to rev it, no increase in power.

This happened after I changed the oil. It's at dead center between H and L on the dip stick (the oil that came out exactly filled the jugs the new stuff came from). I also cleaned the air filter and topped off brake fluid.

41 minutes ago, GTSBoy said:

CVT f**ked. No internet diagnosis beyond that possible.

Which pretty much means car f**ked

 

 

 

 

What did you do exactly to change the oil? And what oil?

4 hours ago, FrankCade said:

This happened after I changed the oil. It's at dead center between H and L on the dip stick

If you mean the trans oil, oil level is checked with engine running and auto in park or neutral, if you filled the same amount that came out and its low, its been low for a loooooong time.

On 4/6/2020 at 12:24 PM, FrankCade said:

I start the car. Push the brake, shift to drive. Push the pedal. It goes forward slightly but then goes back to idle rpm. Flooring the pedal lets me get to ~1500rpm, maybe 2k if I trick it into it, but never move forward again.

Same happens for reverse. It even happens if I start it in neutral and just try to rev it, no increase in power.

This happened after I changed the oil. It's at dead center between H and L on the dip stick (the oil that came out exactly filled the jugs the new stuff came from). I also cleaned the air filter and topped off brake fluid.appvalley tutuapp tweakbox

If you mean the trans oil, oil level is checked with engine running and auto in park or neutral, if you filled the same amount that came out and its low, its been low for a loooooong time.

 
  • 7 months later...

       I had the same thing happen to me last year on my 2010 rogue. It was the TB. That being said I had a check engine pop up though instantly. I could barely rev above idle and I had zero power. I turned it off/on a couple times and it went away and never came back.

If ever it's your CVT, our transmission warranties were extended to 10 years over here in Canada(Presumably worldwide) as Nissan was aware of issues. Mine was fine but I had it replaced last year before the warranty ran out... I just made shit up about it making noise on the highway and It was replaced 2-3 days later. 

Cheers. 

Edited by TurboTapin

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now


  • Similar Content

  • Latest Posts

    • That looks good, but I think you're going to need much beefier side skirts now.
    • They are daft and there's a reason it never caught on. Steering feel? We don't need no stinking steering feel!
    • I gotta pull you up on this. It's driving me crazy. A shutter is something that closes, like over a window or in a cmera. The word you want is shudder. That LSD is clearly f**ked. Take it to a diff shop and get it disassembled and examined by an expert. YOu might have plates welded together or something equally crazy.
    • Define "starting to fail". Wy not just rebuild them?
    • Check the Nistune doco. There are a few assumptions being made here that might not be valid. I will list the things that occur to me: Base map. Base map for what? Base map for Z32? Then the cranking pulse width is probably wrong for an RB25. The extra 500cc of capacity might well be enough to prevent it from catching. Base map for RB25? I don't think you can load one of those into a Z32. You have to just make the settings correct for an RB25 in the Z32 base map. That is either K or the TIM to get the pulsewidth right. Loom. You bought a loom for an RB. And you plugged it into a Z32 ECU. Did you make sure that any iwre differences were swapped. From memory, there's at least a couple. And as per the others, I would suggest making sure that the fuel pressure is correct while cranking and that the injectors are actually flowing as expected. They really must come out and go on the bench, unless you do find that you have messed up as per above points. I would also suggest watching in Nistune to make sure that everything is reading correctly. That the correct binary flags are raised at the right time (like the crank signal), that there's no stupid values in K or TIM. That you have not got mismatched firmware for the ECU and/or a wrong image loaded.
×
×
  • Create New...