Jump to content
SAU Community

V36 key Fobs

Camstad
 Share

Recommended Posts

Camstad Rookie

Camstad

Posted
Posted (edited)

Thought I might add some info for people looking to get a new key and Fob for a Skyline GT370 or similar V36 models

this what I found-

Nissan don't want to know you. although some will try if pushed with info provided by some of the threads here.

Parramatta nissan being one who said they would try {no gaurantee it would work} after telling me the cant do it, they wanted $225 for the pleasure to Program the key.

Mind you some dealers don't have the security module for the consult 111+ scan tool so fair enough.

Keys Fobs , Sinergy motorsports sell them for about $200  genuine JDM import. Key plus Fob - Stock could be problem in the near future

Nissan charge around $380 +

If you can find your part number you could probably get one a bit cheaper directly from a Jap parts website online.

I did also find some second hand units online in Japan about $135-170 posted to Aust.

couldn't find any info whether these can be reprogrammed ?  Let me Know Brains Trust

Programming the key-  there are  a few locksmiths who can do it with a bit of searching, charging $165 for programming. That will vary with each locksmith.

I did find a guy in sydney who could do it with non genuine parts for $350 all up  but who knows what quality you will get.

All in all the process is time consuming and painfull but can be done.

if anyone knows someone in Sydney who can program them cheaper let me know 

Hope this helps

Edited by Camstad
Link to comment
https://www.sau.com.au/forums/topic/481831-v36-key-fobs/
Share on other sites
Zveruga Enthusiast

Zveruga

Posted
Posted (edited)

You can also buy a second hand FOB for like $10 on Yahoo auctions in Japan and get it delivered. Then you need a blank key + outer shell if you want a brand new looking key, altogether around $10 from aliexpress plus get it cut in Bunnings/Mitre10 < $10. Not sure about what happens now but when I needed a spare key for the v36 I found a guy in Melbourne who did it for $150+GST, so altogether under $200 for a brand new key programmed.

Edited by Zveruga
Link to comment
https://www.sau.com.au/forums/topic/481831-v36-key-fobs/#findComment-7946607
Share on other sites
Camstad Rookie

Camstad

Posted
  • Author
Posted

To get your fob programmed i found two people in sydney that can help

Garry from safezone locksmiths on the central coast and Tom from ultimate locksmiths in sydney 

about $160-$170 for the fob to be programmed.

let me know if you can get a second hand fob reprogrammed as it might save a $100 or so off buying a new one.

Link to comment
https://www.sau.com.au/forums/topic/481831-v36-key-fobs/#findComment-7946674
Share on other sites

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now
 Share
Go to topic listing


  • Similar Content

  • Latest Posts

    • Kinkstaah
      Mistakes were made, my R34 Story

      By Kinkstaah · Posted

      How do you propose I cable tie this: To something securely? Is it really just a case of finding a couple of holes and ziptying it there so it never goes flying or starts dangling around, more or less? Then run a 1/8 BSP Female to [hose adapter of choice?/AN?] and then the opposing fitting at the bush-into-oil-block end? being the hose-into-realistically likely a 1/8 BSP male) Is this going to provide any real benefit over using a stainless/steel 1/4 to 1/8 BSP reducing bush?
    • funkymonkey
      Jacks that fit under GTR lips that can reach the subframe?

      By funkymonkey · Posted

      I fashioned a ramp out of a couple of pieces of 140x35 lumber, to get the bumper up slightly, and then one of these is what I use
    • GTSBoy
      Mistakes were made, my R34 Story

      By GTSBoy · Posted

      I wouldn't worry about dissimilar metal corrosion, should you just buy/make a steel replacement. There will be thread tape and sealant compound between the metals. The few little spots where they touch each other will be deep inside the joint, unable to get wet. And the alloy block is much much larger than a small steel fitting, so there is plenty of "sacrificial" capacity there. Any bush you put in there will be dissimilar anyway. Either steel or brass. Maybe stainless. All of them are different to the other parts in the chain. But what I said above still applies.
    • Duncan
      Mistakes were made, my R34 Story

      By Duncan · Posted

      You are all good then, I didn't realise the port was in a part you can (have!) remove. Just pull the broken part out, clean it and the threads should be fine. Yes, the whole point about remote mounting is it takes almost all of the vibration out via the flexible hose. You just need a convenient chassis point and a cable tie or 3.
    • Kinkstaah
      Mistakes were made, my R34 Story

      By Kinkstaah · Posted

      ..this is the current state of that port. I appreciate the info help (and the link to the Earls thing @Duncan). Though going by that it seems like 1/4 then BSP'ing it and using a bush may work. I don't know where I'd be remote mounting the pressure sender... to... exactly. I assume the idea here is that any vibration is taken up by the semiflexible/flexible hose itself instead of it leveraging against the block directly. I want to believe a stronger, steel bush/adapter would work, but I don't know if that is engineeringly sound or just wishful thinking given the stupendous implications of a leak/failure in this spot. What are the real world risks of dissimilar metals here? It's a 6061 Aluminum block, and I'm talking brass or steel or SS adapters/things.
×
×
  • Create New...