Jump to content
SAU Community

Recommended Posts

Hey all.

Been a very long time since I posted here but I wanted to share some info in case it is useful. I've learnt so much on SAU so I need to pay it back!

I recently blew the motor in my R33 - not sure what happened, maybe just age and stress, but it exploded the piston and rod in cylinder 5 very good. In the process it also bent a valve and caused some other damage. In my situation, I decided I would just hunt down a long motor and swap it in. I managed to find a NEO motor for a good price and decided to have a crack. It turned out to be pretty straightforward and runs great.

spacer.png 
The old motor. I didn't place the rod like this, when I took off the sump it greeted me :)

spacer.png 
NEO waiting to go in
 

There's been a bit of discussion that I've found in a few threads in this forum about what you need to do to get a NEO motor into an R33, and specifically if you were going to use the R33 (in my case a series 2) intake and exhaust manifolds. I'm going to list here what I did to get this to work. Hint: it wasn't much.
 

HERE IS WHAT I DID TO GET A NEO MOTOR IN MY R33 USING THE INTAKE AND EXHAUST FROM A SERIES 2 MOTOR:

  • You must swap the VCT Solenoid plug to the "New Nissan" style. I got mine from EFI Solutions here.
    spacer.png 
    Old plug won't fit the NEO solenoid

    spacer.png 
    New plug was straightforward to wire. Pro tip: make sure you get the right crimp tool (you need one that does non insulated crimps)
     
  • You need to swap the CAS wiring if you have the old style metal-cased CAS. (I was lucky, as I have a 40th anniversary R33, my CAS is the same as the NEO CAS, so no change needed). My understanding is the wiring is reversed, but check yourself.
  • I used all accessories from the S2 motor. All brackets fit without modification.
  • I used the S2 Harmonic Balancer, as it has a 2-rib design which matches the power steering pump pulley from the S2
  • I swapped the entire intake. 
    • On the head there are 2 studs for the intake manifold, 1 on either end, to mount the intake along with the bolts. I used the S2 studs as they match the manifold. The ones in the NEO weren't long enough.
    • I was informed that the NEO head has smaller ports. When I did a direct comparison, the difference was basically negligible, and the intake gasket part number is the same between S2 and NEO, so it can't be that different. Nonetheless I did some very slight porting with a die grinder and I haven't noticed an issue.
  • I swapped the exhaust manifold, turbo, etc and it was a direct swap.
  • I added NEO Splitfire Coilpacks - these mount differently than S2 so I couldn't reuse my originals ones, in the NEO they mount directly to the head and not via brackets as seen in the S2.
  • I used my S2 flywheel but they are the same as NEO
  • I swapped to my S2 valve and valley covers, they were a direct swap. This wasn't a must-have.
  • I used the timing belt cover and back plate from the S2 motor
    • On the NEO, the timing belt back plate has a hose that you don't need. Although not a must-do, I swapped to my S2 back plate and cover.
  • I used the S2 thermostat housing
    • The NEO housing is a smaller diameter and overall different dimensions. You could use it find but would need to find the right hose. I simply swapped to S2 and it was bolt on.
  • All cooling and vacuum hoses swapped over without modification
  • Added S2 engine mount brackets
    • These are the same as NEO but new motor didn't come with them.

 

I think this is everything really. There honestly wasn't much to it, when I got everything plumbed it fired up without issue and without touching tune. The biggest change for me was a VCT plug which was nothing, then it was just little bits to make sure it all goes together nicely. As for the end result, you can see a comparison below along with some pics. I did all of this in my driveway basically solo :) 

 

spacer.png 
Old motor, RB25DET S2, 238xxx kms. ARP Studs, Cometic HG, Kelford Springs, Hypergear G3 21U, E85 - 300.4 rwkw
 

spacer.png 
New motor, RB25DET NEO, 250xxx kms, ARP studs, Hypergear G3 21U, E85 - 310.8 rwkw
 

spacer.png 
It wasn't fun in a cold a dusty driveway covered by bunnings gazebos
 

spacer.png 
New motor coming together. New water pump, pulleys and belt
 

spacer.png 
Motor in the car

 

I hope this provides some useful info and helps some of you.

Cheers.

Josh.

 


 

Edited by inmaniac
Formatting
  • Like 6
  • Thanks 2
Link to comment
https://www.sau.com.au/forums/topic/482587-rb25det-neo-into-r33-conversion/
Share on other sites

Congrats on having a go and it being a success .

These are a few things to note if you ever decide to run the Neo inlet manifold and electrics .

The idle air control valve housing is totally different and it's solenoid uses a different plug . Work around is to get one from early N14 Pulsars , or the NA Neos solenoid which use the R33 type loom plug .

Other PITA is if you want to mount the R33's TB/TPS on the Neo turbos plenum - so you can fit up the R33s J pipe and plug in the native TPS . The Neo's bolt pattern is the same but the R33's mount flange is differently shaped so you can't just slap the 33's TB on the Neo plenum . To make it work simply make up a sandwich plate cut to the R33s shape . I was given an old 33 plenum so I cut the TB mount flange off and machined the back flat/square in a lathe .  

Thanks for the heads up on the crank pulley , I didn't know they were different .

I don't have the finances to do a Neo motor yet but I will do the Neo inlet manifold in the not too distant future . 

Cheers A .

 

 

  • 2 years later...
On 11/8/2023 at 12:19 PM, Dylank said:

Out of curiosity what mods have you got to produce the power out put

It would be the turbo, and injectors & management required to fuel it.

A fuel pump would be required, and a FMIC would be expected - you wouldn't get there on the stocker. Turbo back exhaust, ditto.

No mods would be required to the engine.

  • 4 months later...
On 03/07/2021 at 1:03 PM, inmaniac said:

Hey all.

Been a very long time since I posted here but I wanted to share some info in case it is useful. I've learnt so much on SAU so I need to pay it back!

I recently blew the motor in my R33 - not sure what happened, maybe just age and stress, but it exploded the piston and rod in cylinder 5 very good. In the process it also bent a valve and caused some other damage. In my situation, I decided I would just hunt down a long motor and swap it in. I managed to find a NEO motor for a good price and decided to have a crack. It turned out to be pretty straightforward and runs great.

spacer.png 
The old motor. I didn't place the rod like this, when I took off the sump it greeted me :)

spacer.png 
NEO waiting to go in
 

There's been a bit of discussion that I've found in a few threads in this forum about what you need to do to get a NEO motor into an R33, and specifically if you were going to use the R33 (in my case a series 2) intake and exhaust manifolds. I'm going to list here what I did to get this to work. Hint: it wasn't much.
 

HERE IS WHAT I DID TO GET A NEO MOTOR IN MY R33 USING THE INTAKE AND EXHAUST FROM A SERIES 2 MOTOR:

  • You must swap the VCT Solenoid plug to the "New Nissan" style. I got mine from EFI Solutions here.
    spacer.png 
    Old plug won't fit the NEO solenoid

    spacer.png 
    New plug was straightforward to wire. Pro tip: make sure you get the right crimp tool (you need one that does non insulated crimps)
     
  • You need to swap the CAS wiring if you have the old style metal-cased CAS. (I was lucky, as I have a 40th anniversary R33, my CAS is the same as the NEO CAS, so no change needed). My understanding is the wiring is reversed, but check yourself.
  • I used all accessories from the S2 motor. All brackets fit without modification.
  • I used the S2 Harmonic Balancer, as it has a 2-rib design which matches the power steering pump pulley from the S2
  • I swapped the entire intake. 
    • On the head there are 2 studs for the intake manifold, 1 on either end, to mount the intake along with the bolts. I used the S2 studs as they match the manifold. The ones in the NEO weren't long enough.
    • I was informed that the NEO head has smaller ports. When I did a direct comparison, the difference was basically negligible, and the intake gasket part number is the same between S2 and NEO, so it can't be that different. Nonetheless I did some very slight porting with a die grinder and I haven't noticed an issue.
  • I swapped the exhaust manifold, turbo, etc and it was a direct swap.
  • I added NEO Splitfire Coilpacks - these mount differently than S2 so I couldn't reuse my originals ones, in the NEO they mount directly to the head and not via brackets as seen in the S2.
  • I used my S2 flywheel but they are the same as NEO
  • I swapped to my S2 valve and valley covers, they were a direct swap. This wasn't a must-have.
  • I used the timing belt cover and back plate from the S2 motor
    • On the NEO, the timing belt back plate has a hose that you don't need. Although not a must-do, I swapped to my S2 back plate and cover.
  • I used the S2 thermostat housing
    • The NEO housing is a smaller diameter and overall different dimensions. You could use it find but would need to find the right hose. I simply swapped to S2 and it was bolt on.
  • All cooling and vacuum hoses swapped over without modification
  • Added S2 engine mount brackets
    • These are the same as NEO but new motor didn't come with them.

 

I think this is everything really. There honestly wasn't much to it, when I got everything plumbed it fired up without issue and without touching tune. The biggest change for me was a VCT plug which was nothing, then it was just little bits to make sure it all goes together nicely. As for the end result, you can see a comparison below along with some pics. I did all of this in my driveway basically solo :) 

 

spacer.png 
Old motor, RB25DET S2, 238xxx kms. ARP Studs, Cometic HG, Kelford Springs, Hypergear G3 21U, E85 - 300.4 rwkw
 

spacer.png 
New motor, RB25DET NEO, 250xxx kms, ARP studs, Hypergear G3 21U, E85 - 310.8 rwkw
 

spacer.png 
It wasn't fun in a cold a dusty driveway covered by bunnings gazebos
 

spacer.png 
New motor coming together. New water pump, pulleys and belt
 

spacer.png 
Motor in the car

 

I hope this provides some useful info and helps some of you.

Cheers.

Jos

On 03/07/2021 at 1:03 PM, inmaniac said:

Hey all.

Been a very long time since I posted here but I wanted to share some info in case it is useful. I've learnt so much on SAU so I need to pay it back!

I recently blew the motor in my R33 - not sure what happened, maybe just age and stress, but it exploded the piston and rod in cylinder 5 very good. In the process it also bent a valve and caused some other damage. In my situation, I decided I would just hunt down a long motor and swap it in. I managed to find a NEO motor for a good price and decided to have a crack. It turned out to be pretty straightforward and runs great.

spacer.png 
The old motor. I didn't place the rod like this, when I took off the sump it greeted me :)

spacer.png 
NEO waiting to go in
 

There's been a bit of discussion that I've found in a few threads in this forum about what you need to do to get a NEO motor into an R33, and specifically if you were going to use the R33 (in my case a series 2) intake and exhaust manifolds. I'm going to list here what I did to get this to work. Hint: it wasn't much.
 

HERE IS WHAT I DID TO GET A NEO MOTOR IN MY R33 USING THE INTAKE AND EXHAUST FROM A SERIES 2 MOTOR:

  • You must swap the VCT Solenoid plug to the "New Nissan" style. I got mine from EFI Solutions here.
    spacer.png 
    Old plug won't fit the NEO solenoid

    spacer.png 
    New plug was straightforward to wire. Pro tip: make sure you get the right crimp tool (you need one that does non insulated crimps)
     
  • You need to swap the CAS wiring if you have the old style metal-cased CAS. (I was lucky, as I have a 40th anniversary R33, my CAS is the same as the NEO CAS, so no change needed). My understanding is the wiring is reversed, but check yourself.
  • I used all accessories from the S2 motor. All brackets fit without modification.
  • I used the S2 Harmonic Balancer, as it has a 2-rib design which matches the power steering pump pulley from the S2
  • I swapped the entire intake. 
    • On the head there are 2 studs for the intake manifold, 1 on either end, to mount the intake along with the bolts. I used the S2 studs as they match the manifold. The ones in the NEO weren't long enough.
    • I was informed that the NEO head has smaller ports. When I did a direct comparison, the difference was basically negligible, and the intake gasket part number is the same between S2 and NEO, so it can't be that different. Nonetheless I did some very slight porting with a die grinder and I haven't noticed an issue.
  • I swapped the exhaust manifold, turbo, etc and it was a direct swap.
  • I added NEO Splitfire Coilpacks - these mount differently than S2 so I couldn't reuse my originals ones, in the NEO they mount directly to the head and not via brackets as seen in the S2.
  • I used my S2 flywheel but they are the same as NEO
  • I swapped to my S2 valve and valley covers, they were a direct swap. This wasn't a must-have.
  • I used the timing belt cover and back plate from the S2 motor
    • On the NEO, the timing belt back plate has a hose that you don't need. Although not a must-do, I swapped to my S2 back plate and cover.
  • I used the S2 thermostat housing
    • The NEO housing is a smaller diameter and overall different dimensions. You could use it find but would need to find the right hose. I simply swapped to S2 and it was bolt on.
  • All cooling and vacuum hoses swapped over without modification
  • Added S2 engine mount brackets
    • These are the same as NEO but new motor didn't come with them.

 

I think this is everything really. There honestly wasn't much to it, when I got everything plumbed it fired up without issue and without touching tune. The biggest change for me was a VCT plug which was nothing, then it was just little bits to make sure it all goes together nicely. As for the end result, you can see a comparison below along with some pics. I did all of this in my driveway basically solo :) 

 

spacer.png 
Old motor, RB25DET S2, 238xxx kms. ARP Studs, Cometic HG, Kelford Springs, Hypergear G3 21U, E85 - 300.4 rwkw
 

spacer.png 
New motor, RB25DET NEO, 250xxx kms, ARP studs, Hypergear G3 21U, E85 - 310.8 rwkw
 

spacer.png 
It wasn't fun in a cold a dusty driveway covered by bunnings gazebos
 

spacer.png 
New motor coming together. New water pump, pulleys and belt
 

spacer.png 
Motor in the car

 

I hope this provides some useful info and helps some of you.

Cheers.

Josh.

 


 

I'm just wondering how you went on with a ECU I just blown my motor cylinder 1 brought a forged neo just starting to take the engine out and wanting to use a link ECU but which do I order do I order a neo and do they even slot into my original or would I need a adapter for the plug I have a series 1 loom am I better buying a series 2 loom 

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now


  • Similar Content

  • Latest Posts

    • It is a kunfine Android screen . Does anyone know the wirering diagram of the fuga ??
    • just an update to this, poor man pays twice  Tried sanding down the pulleys but it didnt do the trick. Chucked another second hand alternator in the na car which I got for free off my mate and its fixed the squelling. Must have been unlucky with the bearings.    As for my turbo car, I managed to pick up a cwc rb alternator conversion bracket + LS alternator for 250 off marketplace, looked to be in really good nick. Installed it , started the car and its not charging the battery.... ( Im not good with auto elec stuff so im not sure if this was all I needed to do but I verified such by using a multimeter on the battery when the engine was running and I was only getting 12.2v )   I had to modify the earth strap for the new LS alternator , factory earth strap was a 10mm bolt which did not fit the bolt on the LS alternator which was double the size so I cut it off , went to repco bought some ring terminals that fit, crimped it onto the old earth strap and bolted it up to the alternator , started the car and same issue. Ran like shit and was reading 12.2 at the battery.  For a "plug and play" advertised kit thats not very plug and play but alas.  My question is , am I missing something ? Ive been reading that some people recommend upgrading the stock 80 amp alternator fuse to a 140 amp but I dont see how that would stop the alternator charging especially at idle not under load.  Regardless ive pulled it out and am going to get it bench tested by an auto elec tomorrow but it would be handy to know if ive missed something silly or have done something wrong.   
    • My wild guess is that you have popped off an intake pipe....check all of the hoses between the turbo and the throttle for splits or loose clamps.
    • Awesome, thanks for sharing!
    • To provide more specific help, more information is needed. What Android screen? What is its wiring diagram? Does the car's wiring have power at any required BAT and ACC wires, and is the loom's earth good?
×
×
  • Create New...