Jump to content
SAU Community

R34 GTT High pressure power steering hose leak/perished

Bman1296
 Share

Recommended Posts

Bman1296 Apprentice

Bman1296

Posted
Posted

Hi All,

I am experiencing a leak from a repaired (not by me) power steering hose line which comes directly out of the power steering pump and does a U-turn.

Attached is a part diagram to describe the issue, and also a picture of the leak. The green shows the joiner which I believe was a repair job attempted previously, liquid is leaking from the bottom of this. Above the join is another, much smaller leak from a split in the hose. Essentially, the hose is getting old.

Is it possible to get this hose replaced without ripping out the entire system? I have no clue how I would remove this hose, or if this is at all possible. Can I repair it in-situ?

Untitled.thumb.jpg.a6d1464434358a3d04710330724378ae.jpg

ImageImage

GTSBoy Grand Master

GTSBoy

Posted
Posted

You need to do the required disassembly to get that hose all the way out (turbo in & out pipes, probably radiator shroud, possibly radiator, definitely undertray, etc). The repair process from there would be to take it to a hydraulics/hose place and get them to do what needs to be done. Would involve new swaged connections, new hose.

  • Thanks 1
  • 1 year later...
  • 3 weeks later...
Bman1296 Apprentice

Bman1296

Posted
  • Author
Posted
On 3/8/2023 at 9:29 AM, macca911 said:

@Bman1296 - How'd you end up with this? Just noticed the exact same thing on mine. 

 

Cheers! 

Hey, sorry for the late reply. I had to take off the entire part with hose attached, one end going into the banjo joint on the power steering pump and the other part going all the way around to the steering rack. Bit annoying but did it with a bit of flexing under my jacked up car. Then took the whole thing to Pirtek and they put the new hose on. Then reinstalled it. 

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now
 Share
Go to topic listing


  • Similar Content

  • Latest Posts

    • Dose Pipe Sutututu
      Dose's Sometimes DIY and Pay Someone Home & Boat Improvement Thread

      By Dose Pipe Sutututu · Posted

      Wife wanted basket things in the wardrobe in our temporary house. Thought about ripping our the wardrobe and fitting the entire IKEA set, but it's a temporary house and we want to move in a few years. So IKEA advertises this as a 50cm unit, however the actually basket and rails measure 46cm wide. Only issue was depth, IKEA stuff is quite deep, where as the builder special junk is super shallow at less than 40cm. Send it, chopped the rails, then offset the mounting holes, job done, happy wife, less shit scattered all over the bedroom. Did the same to the other side too. Also drove the Skyline shit box today, dropped off oil at Supercheap Auto. I didn't realise they only now take max 2x bottles per visit. I visited 2x Supercheap Autos.  
    • Kinkstaah
      Strange issue RB25DET wont start

      By Kinkstaah · Posted

      I've seen similar actually in my situation. You never know what tables are attempted to be used when the car thinks it's -99C or +200C. The fail state is not usually that extreme but you know what I mean - it was in my case though! This is where being able to read all the sensors is useful cause you see this stuff really quickly.
    • Kinkstaah
      First time Skyline owner

      By Kinkstaah · Posted

      The above is very important. However as long as you keep timing relatively low, it's plausible to make your own knock ears and plausible to learn to tune with a modern ECU that can do wideband O2 correction like a boost controller. I mean if you only have one viable road to even drive the car on, learning to tinker to this level may be worth doing given you can't do much else with the car...?
    • Kinkstaah
      Chris' Toyota Mark ii JZX110

      By Kinkstaah · Posted

      I find the fact that the rear plate has to be bent inwards at the rear not so bad: but the front is just awful: It's like come on. (these are my very old, now retired/turned in plates) TBH it is a lot of money to fix a minor issue, the fact I said "I'll never really spend the money on doing this" is why people ended up buying them as a gift for a 'car guy' who can be hard to shop for.. for car guy things.
    • GTSBoy
      Chris' Toyota Mark ii JZX110

      By GTSBoy · Posted

      I just bent the ends of my premo plates. It even went through Regency like that after the engine conversion and the inspector (a great bloke!) just squinted his eyes and said "I didn't see that". Plates, and how they look, are just something that have zero importance to me.
×
×
  • Create New...