Jump to content
SAU Community

Recommended Posts

Have been trying to tackle an issue with my R32 GTR's climate control unit for a while now, and finally got some time to try and work out what's wrong. Basically, when I push the 'mode' button, it doesn't change where air is blowing - nor when I push the windscreen button. The door mode actuator just doesn't seem to move at all. Here is what I have done and found so far, but i'm honestly stuck at this point:

  • I've pulled the mode actuator out and pulled the 'locking' gear off, and re-plugged the unit in - and when attempting to change modes the actuator arm still doesn't spin (however, it can now be spun by hand).
  • When carrying out the diagnosis built into the climate control unit, I get the '31, 32, 34, 35, 36' pattern displayed when in Step 3 - door mode position check. This indicates a connector issue, but the connector is definitely plugged into the actuator.
  • The voltage from the pins on the loom that plugs into the actuator doesn't appear to change when I change modes - I thought they would (for example, I thought it would read different when at 'feet' vs 'windscreen'. The voltage readings I got (going from left to right with the pins at the bottom) were: 0v, 0v, 0v, 0v, 4.7v, 4.7v, 0v, 4.7v, 4.7v, 0v.

Any help or assistance here would be much appreciated.

 

On 7/17/2022 at 5:55 PM, GTSBoy said:

Mode door actuator failure is very common. Pain in the arse to swap out too.

Possibly a bit of a positive / update. I removed the motor, and manually applied power to it and it spun happily both ways. The contacts themselves all seem to respond when they should when the main trigger wheel contacts the metal inside as well. Regardless, I pulled the motor apart and cleaned all the metal contacts, re-greased them with electrical grease and greased the gears. So it actually looks like the mode door actuator is in good working order.

However I now have no idea where to start looking from an electrical perspective. I'm hoping the central, main climate control unit isn't the culprit - but I believe that will have to be my next check. Just I don't know what I should be expecting it to do.

Edited by Dyzzii

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now


  • Similar Content

  • Latest Posts

    • Clutch is a spec brand, new clutch system,( PP, flywheel, friction disc, etc. pull type) installed 100 miles ago, with no problems.
    • looking for some help and maybe some insight on others experience with a new LSD. R34 GT ran and drove beautifully, but always alot of grip loss due to the open R200 rear end, so I just installed a new 1.5 LSD way into the stock open R200 for a ER34. Simple. Everything seemed right. I test drove for the first time this weekend. as I started to back out the garage the first time slowly with tires straight it sounded and felt like I had a loose or half disconnected drive shaft...that was clucking around loose and shaking entire vehicle, and making it feel like the trans clutch was spontaneously slipping then grabbing very roughly while just letting out pedal slowly. I backed it out went to pull forward with the same noise, shake and slip grab feeling with hesitation, I turned the tires to back out more and then pulled ahead some same thing but worst because of added wheel resistance (which that I expected) puzzled … pulling it back in checking everything over and finding nothing wrong, I tried it the next day. same thing, couldn’t believe how it shook everything again making a terrible noise and making it feel like the trans clutch was slipping and grabbing, but I got it out of garage into the driveway, got it straight, drove forward and then reveres a few times in a straight line everything shaking , causing what felt like clutch slip and grab every time, sounded like right behind front driver tire and I could feel it in the floor board with my feet,... worst right when beginning to let clutch pedal out to engage slightly, shuttering and sounding terrible along the way…I managed to slowly get down the road, babying it the whole way, once I was rolling (out of 1st) seemed to be better and between shifts, then clutch felt closer to normal…not slip/ grab etc., but back down to any stop, straight road or turning, same thing. Made no difference if all tires were straight or if I was turning. All other gauge read out correct. with in 2 miles as planned I reached the empty parking lot and performed the break in procedure that came with lsd, essentially to drive in a figure 8 a bunch.  Did this, binding chattering, and shaking the car the whole way. I drove it back home seemed somewhat normal once I was in straight line and past 10 mph or so, and I know it will “bind” on corners and cause some tires squeal when turning especially from a stop, but when I begin to move it still causes what feels like the trans clutch to slip and jerk badly as well as shaking the entire car, and sounds terrible, that I didn’t expect. I used the fluid they supplied with LSD kit and did the breaking, planning to change fluid as they suggest after breaking, but wondering will it get smoother or less aggressive with use? maybe a 1.5 is just too aggressive for normal road driving?   I have a LSD that I put in my 71 cuda when I restored it, with amazing smooth , quite yet effective results. Different style LSD but that ones a joy to drive. maybe expecting too much from this R200?
    • Join SAU NSW for a flame-grilled feed & flame-spitting cruise! Sunday 17th August 2025 3:30PM Meeting Archies Flame Grille Sylvania Waters 4:45PM Cruise Departure 5:15PM Arrival at Cape Solander Kurnell Meet Location: Archies Flame Grille Final Destination: Cape Solander Kurnell *Disclaimer* There will be a lead and follow car so no one should get lost. If you would like to attend or bring others along please put your name down and a +1 as numbers will be needed prior! This is NOT a race and we will all be adhering to all road rules. If this is what you want please come to one of our many track days. This is an official SAU:NSW event and will be run under a CAMS permit. One of the things that really sets our club apart is our commitment to being true enthusiasts. When on normal roads we strive to maintain good relations with the authorities as well as the public in general. When attending one of Skylines Australia NSW events please try to: • Be aware of surrounding environment and act accordingly. • Drive courteously on the state’s roads as a true enthusiast should. • Understand how important it is to maintain the good name of SAU NSW and thus, treat others accordingly. • Any misbehavior will not be tolerated and you will be asked to leave.
    • Yeah good luck out there! Will be good to see a mighty GTST going harder than the GTRs
    • i will be there 😁
×
×
  • Create New...