Jump to content
SAU Community

Transmission wont mate with engine

Prof_Finesser
 Share

Recommended Posts

Prof_Finesser Enthusiast

Prof_Finesser

Posted
Posted

Hi everyone I recently built my r32 rb25de and was putting on the transmission and cant seem to get it on all the way.  I'm using an action clutch kit and flywheel.  I had the alignment tool in when installing as well.  I put the trans on and it feels like its in also when I spin the crank it does spin the trans so I'm not too sure what to do.  Going to try and take off the PP and reinstall it.  Maybe the clutch isn't aligned right.  Any suggestions help.  Also its a normal single disk clutch.

Link to comment
https://www.sau.com.au/forums/topic/484232-transmission-wont-mate-with-engine/
Share on other sites
The Bogan Grand Master

The Bogan

Posted
Posted

Some clutch alignment tools are better than others

Start to tighten down the plate until it just holds, then wobble the alignment tool to center the plate, clutch and flywheel, then tighten it up to spec

If you just put the alignment tool in and tighten it up they sometimes don't align correctly because the plate is hanging a little low creating an angle

Neostead2000 Enthusiast

Neostead2000

Posted
Posted

I had issue with this also the other day when I was attaching the gearbox to the motor. What did the trick was a bit of grease (not much) on the tip of the input shaft so it goes in nice into the pilot bushing, after the tranny was slightly in and making contact with the clutch plate (confirmed by rotating everything), I took a big block of wood, positioned it at the tail end and started whacking it with a big hammer. Surely enough, it started going in. Then I threaded in the 4 long bolts just a bit and kept hitting it and threading the bolts until the trans went flush with the dowel pins. Of course had to make sure the gearbox was aligned good when hitting it from the back, it was 2 of us doing it.

Prof_Finesser Enthusiast

Prof_Finesser

Posted
  • Author
Posted

I got it mated and the engine is back in the car what helped me was i had the trans sort of connected and it was on the ground so I sat down and put the feet on both sides of the trans and pushed it in.  Thank you guys for the info and suggestions.

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now
 Share
Go to topic listing


  • Similar Content

  • Latest Posts

    • nouveau_poor
      Unknown sound similar to BOV on positive boost with partial throttle RB26

      By nouveau_poor · Posted

      I certainly fall into the annoyed camp, but glad to hear that if it's happening at low boost then I'm not likely going to blow a turbo and end up with metal shards in my oil. Just feels like it prevents me from really driving it without hesitation and "peak" performance. Wonder if it's the VCAM, it did an impressive job of shifting the torque curve and faster spool, but maybe now it's "too fast" and there's too much air for how open the throttle is.  Based on some other threads, will also do some reading on synchronizing the actuators. They are the default actuators that come on the Garrett's and I would think they would be set the same coming from the factory, but if the turbos don't actually work exactly the same way at the same time as previously mentioned, it would be worth making sure the actuators are actuating together properly
    • GoHashiriya
      R34 Skyline Sunroof Won't Tilt/Vent

      By GoHashiriya · Posted

      I went down this rabbit hole before, ended up sourcing a motor from the UK (I'm in Japan) which also didn't function correctly. With the original motor, I disassembled it and reassembled it and it works somewhat, sometimes. What I could deduce from all my screwing around is that there is calibration of the gears on the inside of the motor and two ramps on the main gear which activate switches that operate the motor and move the sunroof either to retract into the roof or tilt. Where I got stuck was that, it seemed in my case that one or both of the switches that are activated by the ramp on the gear did not always activate and thus the motor did not move, causing it to sometimes not retract or tilt (apologies, I've forgotten which way it didn't work.).  Of course this part is discontinued at Nissan now, it's the same part in the S15 but no other models. I also contacted the manufacturer of the component for schematics - forgot the name, they're based in Gifu - but they declined to share the information due to being bound by an NDA, sadly. Looking through my pictures now, it seems I last had a crack at this in 2022. See, I so kindly wrote "open" and "close" next to the switches. If you figure it out, please do tell me. Those little switches, with the red buttons may need to be replaced.
    • GTSBoy
      R34 Skyline Sunroof Won't Tilt/Vent

      By GTSBoy · Posted

      Something's broken.
    • PranK
      Shoota's R33 GT-R RB30/26

      By PranK · Posted

      It says 300ZX, does that make it an Aus delivered car? Funny how back in the day I just couldn't care less about Z32's and these days I am just in love with them. Back when Nissan was into pushing the envelope. 🤣
    • ShezzDogs
      R34 Skyline Sunroof Won't Tilt/Vent

      By ShezzDogs · Posted

      Hi guys, just after some guidance with an R34 sunroof that has stopped working correctly. It still opens and closes perfectly fine, but it no longer tilts/vents up or down. As a result, the rear of the glass now sags a bit as it drops down slightly in order to retract into the roof, but now it can't pop upwards into a flush position. I’ve probed the pins on the back of the switch connector with a multimeter and it seems like both switches (for open/close and tilt/vent) still work correctly. Any ideas on what it could be, or where I should even start in terms of diagnosing? I'm sure someone's had this issue before but I haven't been able to find anything online relating to this specific issue, most of the issues are with the seals leaking or the motor failing entirely. Thanks in advance!
×
×
  • Create New...