Jump to content
SAU Community

Recommended Posts

Hey Sau,

Long time lurker. I just wanted some opinions from the experienced guys to see if this block is still useable or if it's a boat anchor and I should try get my money back? My concern is this crack between the water jackets to the head bolt thread between cylinder 3 and 4 see picture attached. Little back story about it, I bought it as the start of a small build to put into my daily. Was told was running fine no issues the previous owner had just pulled it down to go forged bottom end lost motivation and was now selling if off, after I started to clean it up I found the crack. The target I'm aiming for would be between 375 - 450kw so not the biggest power output but as it's going into my daily ( probably in the year 2050 at this rate) I'd like to give it a chance at surviving for as long as possible. 

crack in deck rb26.PNG

As far as I know the spot that breaks most commonly is on the exhaust side, adjacent to #4 or between 4/5. So any unnecessary weakness on the exhaust side, even if it's not is the "usual" spot, can't be a good thing. And between 3 & 4 is not so far away from where the block likes to jump to pieces.

Thanks for replying so quickly and sharing your knowledge. I had heard of the block issues between cylinder 3 and 4 splitting and the crack on the outside of the block from block twist after a healthy amount of power put through them but this is all new to me. When I spotted it I thought it might be a drama but was hoping it was more superficial so I could finish making the deck flat give it a hone and get down to ordering some parts, looks like I might have to start getting in touch with the seller to try get my cash back. 

Mine has a crack from water gallery to headstud hole in-between 5&6... Sent it back together, been a year so far at 520kw and had no dramas yet .. I guess it all depends if you are prepared to do all that work to potentially do it all again 🤣

Edited by BrynDETT
  • Like 1
  • 2 weeks later...

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now


  • Similar Content

  • Latest Posts

    • Ahhh, I need the whole head unit. I definitely needed to roll back through and review your setup, ha ha! Neat setup they have going on. I just need a full double din head unit. But I want good and responsive. I might have to review what the likes of pioneer have out these days.
    • Ok so after much research and talking with knowledgeable people I've got my turbo conversion done and it's all running great other than 1 small issue.  Car has remained auto with the na auto and tcm, I've used a stagea ecu with. NIstune board and everything is great other than my gear selection on the dash. It illuminates park, reverse, neutral, 3rd and 2nd. But nothing drive or what gear your in when you pop it into tiptronic.  I'm sure there is may e 1 wire in the ecu plug I need to move to rectify this. Dose anyone here have any ideas?   Cheers guys
    • Sorry I haven't been following all the detail, so you may have tried this. Does it idle with the tiniest bit of throttle you can add? You've mentioned the IACV, does it have an AAC valve and have you adjusted it at all (ie, screw the idle adjust screw all the way in, then back it out a couple of turns until idle is stable)?
    • My bad, I unplugged the one underlined in red instead of yellow before. With the car started, after unplugging the IACV (the one underlined in yellow), it idled at around 400/500 for 3 seconds before stalling. Attempting to start the car without the IACV will not start the car.   It does stutter and sputter for around 5 seconds before dying. However, immediately after starting it, you can already hear some slight sputters from the exhaust.   It won't start with the AFM unplugged. If it is when the car has already started, it stalls in a few seconds.   Yesterday, I did take some logs using Nistune of 3 scenarios. Car idling till it stalls Car idling and unplugging the IACV Car idling and removing the AFM I also have some previous logs of when the Car is idling till it stalls and when driving and it cuts. I am not really knowledgeable enough to understand what to look for. After every test, car idles rougher and rougher, until I have to stop. It will be fine the day after.
    • There is no difference between a 17x8 and an 18x8. The total diameter of the tyre needs to remain +/- the same (so you don't mess up the gearing, speedo reading, and clearance when turning front wheels..... so you just need to use a lower profile tyre on th 18 than you do on the 17. /rocket surgery.
×
×
  • Create New...