Jump to content
SAU Community

Recommended Posts

Hi,

if had the car for around 3000km now. Since the last 750km the transfer case started to leak. I have degreased it a few times and after a drive the drips are already hanging under the case. It’s red of color so I am sure it is ATF fluid. The case or gearbox has not been removed. I did change the gearbox oil to redline to get rid of a grind in fourth, but thats it. What are the most common causes of these cases to start leaking? 
 

Also when shifting I feel the car does a hard clunk even when letting the clutch get up slowly. Its like something gets a snap due to getting power from the engine. If that makes sense.

 

Hope someone can narrow it down for me. Can’t get the car in the air to verify more. Would need to go to a shop for that. 
 

cheers! 

C29372EA-2475-4AF5-892A-8D1CAB66725C.jpeg

14C6A8F0-4E6E-4F9F-A075-6E10D3B85D78.jpeg

4244E698-97EE-410C-89E0-EB3D3DD019F4.jpeg

Edited by T.Krol
Spelling error
1 hour ago, T.Krol said:

Hi,

if had the car for around 3000km now. Since the last 750km the transfer case started to leak. I have degreased it a few times and after a drive the drips are already hanging under the case. It’s red of color so I am sure it is ATF fluid. The case or gearbox has not been removed. I did change the gearbox oil to redline to get rid of a grind in fourth, but thats it. What are the most common causes of these cases to start leaking? 
 

Also when shifting I feel the car does a hard clunk even when letting the clutch get up slowly. Its like something gets a snap due to getting power from the engine. If that makes sense.

 

Hope someone can narrow it down for me. Can’t get the car in the air to verify more. Would need to go to a shop for that. 
 

cheers! 

C29372EA-2475-4AF5-892A-8D1CAB66725C.jpeg

14C6A8F0-4E6E-4F9F-A075-6E10D3B85D78.jpeg

4244E698-97EE-410C-89E0-EB3D3DD019F4.jpeg

Transmission or engine mounts need to be replaced if you get bad shift shock even with a lot of clutch slip. The back of the transfer case is probably leaking where the hose connects. It’s a high pressure hydraulic system so leaks are inevitable with age. To be sure you need to clean it off and then repressurize the system while under the car. 

  • Like 1
4 hours ago, joshuaho96 said:

Transmission or engine mounts need to be replaced if you get bad shift shock

And while that can be true, it is also possible that the clunk comes from the tailshaft centre bearing, from the diff CW&P lash, from CVs or the splines of the driveshafts into the hubs, etc. Also possible to be in the front drive stuff, but you wouldn't expect anything there to cause much noise on a normal takeoff.

  • Like 1
2 hours ago, GTSBoy said:

And while that can be true, it is also possible that the clunk comes from the tailshaft centre bearing, from the diff CW&P lash, from CVs or the splines of the driveshafts into the hubs, etc. Also possible to be in the front drive stuff, but you wouldn't expect anything there to cause much noise on a normal takeoff.

Good point, there’s a whole class of failures I forgot about that can also cause this. 

Thank you. I did read that the clunk noise can have many different causes. I guess the car needs to go in the air to figure that one out. I did go ahead and ordered this product: https://frenchysperformancegarage.com/collections/nissan-skyline-r32gt-r/products/fpg-bnr32-attesa-high-pressure-hose-replacement-with-optional-pressure-sensor-adapter-fpg-116?variant=42829932724402.

Since I am quit sure that the leak is coming from the Attesa hose. Also it might be leaking at the Atessa pump above the read diff, since I do get a bit of oil leaking from the right side area of the rear-diff, also red colored oil.

Is it harmful to drive every now and then with the car with this small leak?

 

24 minutes ago, T.Krol said:

Is it harmful to drive every now and then with the car with this small leak?

Not if it is actually just a small leak. Just watch your level. But, it could also transition into a really big leak at any moment, and that could be destructive.

so, as I mentioned in another thread on this leak recently, just back off the attessa line where it goes into the rear of the transfer case about 1/2 turn (or 12 turns if I can't type), then tighten it up again. Give everything a thorough degrease and see how it goes.

you can monitor the level of that fluid in the reservoir in the boot, just top it up if necessary

Reservoir was almost at max level without ign on. Topped it off but did a lil too much. I am 8-10mm above max level. Tried to put the ign on and see what it did but it stayed at that level. Is that allright to run the car with a little over max? Havnt turned the car on yet to check the level. 

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now


  • Similar Content

  • Latest Posts

    • Sounds like you've got an interesting adventure ahead here with local support if you have trouble! My guess is that, unboosted, you will be OK with a small upgrade like -9. What will happen is that once the stock ECU sees more airflow than it expects it will add a heap of fuel and pull a heap of timing to be safe because it can't understand how it could get that much air without there being an issue. You will see clouds of black smoke and it won't pull hard through the midrange and top end. So, overall it will be a bit frustrating but should be OK. If you are still nervous set the base timing back 2o through the CAS, but it will be even more sluggish everywhere. As said above through...this is not my guarantee your engine won't be blown into a million pieces, leaving you looking for very hard to find parts A better idea is get a computer with logging ASAP, wire in a wide band O2 sensor and a use remote tuner. I've done multiple cars this way and while it is not as good as a specific tune on a dyno they can get it 90% right. I'd suggest if you can afford an R33 GTR these days you can afford an ECU and tune. And if you can't afford that you sure won't be able to afford the rebuild if it goes bad in the meantime,.  
    • Yeah it would be nice if someone took the time to put that sort of information together, but there are a lot of variations in looms. I think you are making this way hard for yourself if you just want to get it running....sourcing an SR20 with the right wiring will be a billion times easier than matching the RB loom to an S15 chassis. If you do end up going this way, you just need to trace every wire in the loom with a multimeter, 95% of them will go to a location you can confirm at the ECU.....and then post it up for the next person who needs it  
    • Just top it up with water, and keep a general idea of how much you added. It is normal for water to be pushed into and pulled out of the reservoir through the cap, and it should not be more than half full or it will be likely to overflow when hot. Any decent mechanic can do a pressure test of the cooling system to confirm if you have a leak. Keep in mind if it is only leaking a little and when hot it may well evaporate before you see it hit the ground
    • I'd ask the shop what they used and use that. Mixing coolants is sometimes OK, sometimes not, and you have know the details of each coolant to know whether it's a good idea or not.
    • Is it alright to top up with just another green coolant?
×
×
  • Create New...