Jump to content
SAU Community

CES Split dump pipes


Recommended Posts

  • Replies 56
  • Created
  • Last Reply

Top Posters In This Topic

Guys, CES is one of the Best exhaust fabricators in Australia

Goto www.cesracing.com.au to read about them

All ive ever heard about CES has been good

$650 for this; HPC coated is awesome!!

If we get 10 im in definate.

Guest darrinspencer
Wizard count me in for sure as long as i can pick up the dump pipe within the next couple of weeks. I am very interested... Also what would be the difference between the plain steel and the HPC coated?

The $650 price is for 10 steel pipes HPC coated

If we split them up, some with HPC and some without It will adjust the $650 price

Prices quoted were broken up as

10 pipes $530 each plus hpc $120 each total $650 each

5 pipes $550 each plus hpc $130 each total $680 each

So depending on what option we end up with the final cost may be affected

One thing Trevor suggested was that on Skylines with their fairly low mount of the turbo the HPC would have a less of affect and you could get away from not using it.

Apart form the high heat reducing affect from HPC, it also stops the mild steel pipe from rusting, which IMO is worth while.

There seams to be a few GTR owners keen to participate in this group buy. If it was possible to include dump pipes for an R32/R33 GTR in the group buy I think you would make up the numbers required a lot quicker. I would be keen for starters...

Lawrence

Guest darrinspencer
There seams to be a few GTR owners keen to participate in this group buy. If it was possible to include dump pipes for an R32/R33 GTR in the group buy I think you would make up the numbers required a lot quicker. I would be keen for starters...

Lawrence

We need to get 10 people for 1 type of dump pipe not a mix up of both

CES make 10 at a time, hence we need to get 10 people together for 32/33 GTST to get the better price.

To organise a group buy is a pain in the arse for who ever organises it.

Some people want one, some are interested but do not confirm if they want one, some want one then pull out when it is time to pay which really stuffs things up as it has recently happened in my last group buy for flywheels

I am only doing this so I can get a cheaper price for my car.

If you want to organise a GTR dump pipe group buy feel free.

Guest darrinspencer
There seams to be a few GTR owners keen to participate in this group buy. If it was possible to include dump pipes for an R32/R33 GTR in the group buy I think you would make up the numbers required a lot quicker. I would be keen for starters...

Lawrence

I will be now including GTR as aswell

I will update the first thread soon with prices when I can fit it in between work.

Guest darrinspencer
There seams to be a few GTR owners keen to participate in this group buy. If it was possible to include dump pipes for an R32/R33 GTR in the group buy I think you would make up the numbers required a lot quicker. I would be keen for starters...

Lawrence

GTR and GTST are now included in the group buy

Please read the first thread for all the details and prices

Please read the group buy rules aswell.

Thanks

NewB question... what the hell does the waste gate do?? Is it essentially there to create less turbulence as the two exhaust streams meet at a similar velocity?? I'm not too sure.

BTW this will bolt straight on to a stock R33 GTS-t?? If so, is it a DIY jobby?

(In case ur not sure ,I am seriously interested in one of these... just depends on when I can get it etc.)

Cheers.

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now



  • Similar Content

  • Latest Posts

    • Hi, is the HKS  Tower Bar still available ? negotiable ? 🤔
    • From there, it is really just test and assemble. Plug the adapter cables from the unit into the back of the screen, then the other side to the car harness. Don't forget all the other plugs too! Run the cables behind the unit and screw it back into place (4 screws) and you should now have 3 cables to run from the top screen to the android unit. I ran them along the DS of the other AV units in the gap between their backets and the console, and used some corrugated tubing on the sharp edges of the bracket so the wires were safe. Plug the centre console and lower screen in temporarily and turn the car to ACC, the AV should fire up as normal. Hold the back button for 3 sec and Android should appear on the top screen. You need to set the input to Aux for audio (more on that later). I put the unit under the AC duct in the centre console, with the wifi antenna on top of the AC duct near the shifter, the bluetooth antenna on the AC duct under the centre console The GPS unit on top of the DS to AC duct; they all seem to work OK there are are out of the way. Neat cable routing is a pain. For the drive recorder I mounted it near the rear view mirror and run the cable in the headlining, across the a pillar and then down the inside of the a pillar seal to the DS lower dash. From there it goes across and to one USB input for the unit. The second USB input is attached to the ECUtec OBD dongle and the 3rd goes to the USB bulkhead connected I added in the centre console. This is how the centre console looks "tidied" up Note I didn't install the provided speaker, didn't use the 2.5mm IPod in line or the piggyback loom for the Ipod or change any DIP switches; they seem to only be required if you need to use the Ipod input rather than the AUX input. That's it, install done, I'll follow up with a separate post on how the unit works, but in summary it retains all factory functions and inputs (so I still use my phone to the car for calls), reverse still works like factory etc.
    • Place the new daughterboard in the case and mount it using the 3 small black rivets provided, and reconnect the 3 factory ribbon cables to the new board Then, use the 3 piggyback cables from the daughterboard into the factory board on top (there are stand offs in the case to keep them apart. and remember to reconnect the antenna and rear cover fan wires. 1 screw to hold the motherboard in place. Before closing the case, make a hole in the sticker covering a hole in the case and run the cable for the android unit into the plug there. The video forgot this step, so did I, so will you probably. Then redo the 4 screws on back, 2 each top and bottom, 3 each side and put the 2 brackets back on.....all ready to go and not that tricky really.      
    • Onto the android unit. You need to remove the top screen because there is a daughterboard to put inside the case. Each side vent pops out from clips; start at the bottom and carefully remove upwards (use a trim remover tool to avoid breaking anything). Then the lower screen and controls come out, 4 screws, a couple of clips (including 3 flimsy ones at the top) and 3 plugs on the rear. Then the upper screen, 4 screws and a bunch of plugs and she is out. From there, remove the mounting brackets (2 screws each), 4 screws on the rear, 2 screws top and bottom and 3 screws holding in the small plates on each side. When you remove the back cover (tight fit), watch out for the power cable for the fan, I removed it so I could put the back aside. The mainboard is held in by 1 screw in the middle, 1 aerial at the top and 3 ribbon cables. If you've ever done any laptop stuff the ribbon cables are OK to work with, just pop up the retainer and they slide out. If you are not familiar just grab a 12 year old from an iphone factory, they will know how it works The case should now look like this:
    • Switching the console was tricky. First there were 6 screws to remove, and also the little adapter loom and its screws had to come out. Also don't forget to remove the 2 screws holding the central locking receiver. Then there are 4 clips on either side....these were very tight in this case and needed careful persuading with a long flat screw driver....some force required but not enough to break them...this was probably the fiddliest part of the whole job. In my case I needed both the wiring loom and the central locking receiver module to swap across to the new one. That was it for the console, so "assembly is the reverse of disassembly"
×
×
  • Create New...