Jump to content
SAU Community

Garage Sale-everything must go

Clint32
 Share

Recommended Posts

Clint32 Mentor

Clint32

Posted
Posted

rb25 coild packs, all 6 on mount barackets, selling due top upgrade $200

R32 gtst rear seats exe conditon $100

RB25det std cams $200 pair, exc condition no marks

RB20 engine fan and clutch $50

GT wing, adjustable, black, $100

r32 gtst rear hicas steering rack with both pumps and lines etc $100

rb25 alternator $100

rb20 lower plenum runners, $40

rb20 throttle body no tps, $20

R32 steering wheel ok conditon , no major tears, has wear marks, $30

all prices neg need to sell otherwise stuff will go in the bin, in adelaide but will ship at buyers expence, email [email protected] for more info or if you need pics

Link to comment
https://www.sau.com.au/forums/topic/48880-garage-sale-everything-must-go/
Share on other sites
krzysiu Grand Master

krzysiu

Posted
Posted
R32 gtst seats, exc condition, both front and rear included $150

R32 gtst power steering pump and resivoir $50

R32 air conditining condenser and pump, lines etc, everthing to do with the setup $50

RB25det exhaust manifold $50

RB25det injectors and fuel rail, $100

RB25det BOV and crossover pipe $50

RB20 engine fan and clutch $50

GT wing, adjustable, black, $100

Rear camber arms r32 suit gts/gtr/s13 with adjustable urathane  bushes $50

r32 gtst rear hicas steering rack with both pumps and lines etc $100

std r32 steering wheel advarage condition $30

rb25 alternator $100

more parts will be added shortly

all prices neg need to sell otherwise stuff will go in the bin, in adelaide but will ship at buyers expence, email [email protected] for more info or if you need pics

Pics of GT-Wing to [email protected] thx

Clint32 Mentor

Clint32

Posted
  • Author
Posted
Could you please advise a cost to send the front and rear seats to Gold Coast Qld? postcode 4211.       They are precise;y what i am after.

Cheers

will do, will probably be more than the seat though

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now
 Share
Go to topic listing


  • Similar Content

  • Latest Posts

    • MBS206
      Cas issue

      By MBS206 · Posted

      Have you done the Ignition Sync Wizard in the AEM software?
    • MBS206
      R32 GTS (RB20DE) Injectors Replacement

      By MBS206 · Posted

      Find out what RPM it was idling at with the IACV unplugged. It's very weird that the rpm didn't change at all, and then it stalled. When it stalls is it nearly like a switch off, like you've turned the engine off? Or is it more stutters and sputters and coughs to death over a few seconds? Or does the RPM just slowly keep going down and down? Have you done a test of trying to start it with the AFM unplugged? Does it still die?     If you Follow Josh's advice on using Nistune to check the voltages (which is a perfect method!) if you see anything out of wack voltage wise, THEN get the multimeter out and read the voltage directly at the sensor. If the two vary, then you're now looking for a wiring issue vs a sensor issue. So be aware, what the ECU sees, may not be what the sensor is actually saying too...
    • MBS206
      RB25DE NEO with Haltech ECU

      By MBS206 · Posted

      You very likely need to get it on a dyno and tune it. My assumption is, you've got an RB25DET tune in it, which has a different manifold, different injectors, and different cams as a minimum. What O2 sensor are you running?   When you say it runs extremely rich from idle all the way to redline, is this just free revving it you see that?
    • Haggerty
      RB25DE NEO with Haltech ECU

      By Haggerty · Posted

      I seem to the be only person that is using a Haltech 2500 on an NA motor, I've installed a Bosch DBW throttle body to the OEM intake manifold and am having problems maintaining AFR even with the wideband o2.  It will run extremely rich at idle and up to redline, but under load it will go extremely lean in the 20s and i'm essentially having to rev it over 4k and feather the clutch to get it up to speed.  I've read a few other threads of about the butterfly, it seems removing the vacuum to it is supposed to have it remain open, i've noticed no difference under 4k with the vacuum line to it plugged.  I'm hoping someone here has had luck using the NA manifold with Haltech, and if they happen to have a tune for it.  
    • sonicii
      Could it really happen......

      By sonicii · Posted

      I don't know any details, but I really wouldn't be surprised if they do it as a LHD only version, at least initially.
×
×
  • Create New...