Jump to content
SAU Community

Recommended Posts

Gday,

I know this has been done before (I"ve searched and read). But I'm after recommendations of either people from these forums who work in a shop, or have got this done by one.

I'm looking into getting a r32 auto and swapping with rb25det and manual conversion with the rb25det matched gearbox. Either that or buying a manual rb20det and then doing engine conversion.

Anyone have any recommendations? And also price estimates?

Would I be looking at $5000 ish or $10,000ish ?

This is not including computer or tuning. Just engine and gearbox swap. Also this does not include diff (I'm assuming you need a stronger one if you wanna do bulletproof driveline).

Thanks.

Link to comment
https://www.sau.com.au/forums/topic/49069-workshops-to-do-rb25-swap-r32/
Share on other sites

Thanks texas :P

Have you dealt with these guys?

I've also heard of autostyle and unique auto sports but i prefer to give my business to some nice guys who CARE and are enthusiasts.. HOT4s garages (in my mind) seem a bit more into the money side of cars :(

I have had a number of cars done with Fred and Brett and honestly, you'll not find a pair of fairer or more honest people.

Autostyle - I will not comment, just that people here have some strong feelings about them.

UAS are fine but they are not in the conversion field.

For this kind of work, it's best to talk to people who know how to do conversions.

T.

Either way unless you are very careful you may get taken for a ride..

To be honest trying to tackle it yourself is an option compared to some stories and prices I have seen from workshops.. You can fug up a hell of a lot of things, but at least its in your own time and not your money. Many times a workshop will make much the same mistakes as you might, but they'd be charging you for *their* mistakes and research time. Some places would charge you $10,000 for that sort of conversion.

Unless the workshop has definitely done a couple of the exact conversions, can quote you a fairly firm price (based on the other conversions) and you can see the results for yourself.. I'd be just doing it yourself.

As you can tell I don't have much faith in mechanics these days :P

The tricky part is getting the RB25 ECU to work with the R32 instruments and aircon etc.

Not rocket science but you definitely want someone who has done it before and isn't 'experimenting' with your car and money.

That's why I recommend someone who's done it to his own car.

T.

my mechanic can and has done it before we were going to do it to my car but we found an RB26 for a good price.

he does jobs like that in a weekend, drop it off friday night pick up sunday arvo, so its not as hard as it sounds.

PFC wont make it easier weith the wiring because it still has to be the standard loom.

You're best off dropping the engine in if at all possible yourself.. getting everything hooked up.. then calling up an auto-elec familiar with RB's to sort the wiring.

The wiring is the messy part, but any workshop will probably just call in an auto-elec at the end anyhow.

  • 3 years later...

I just got my RB25DET (series 2) and I was hoping you could help me with some questions.

My Skyline is non turbo so it will be a big step with the RB25.

Now then, my first question is about the gearbox mounts, I hear they aren't the same and I will also have problems with the speedo meter. What do you know about this? Can I use the Xmember of the R33 ??

The second is about the harness, everyone that has ever swapped an engine told me that the harness is the most difficult part of the swap. Do you have the diagram of the R32 and the R33 (still can't find it for the R32) and some pointers on how this is done??

Hope to get a reply from you soon

Carlos Rudolph

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now


  • Similar Content

  • Latest Posts

    • From there, it is really just test and assemble. Plug the adapter cables from the unit into the back of the screen, then the other side to the car harness. Don't forget all the other plugs too! Run the cables behind the unit and screw it back into place (4 screws) and you should now have 3 cables to run from the top screen to the android unit. I ran them along the DS of the other AV units in the gap between their backets and the console, and used some corrugated tubing on the sharp edges of the bracket so the wires were safe. Plug the centre console and lower screen in temporarily and turn the car to ACC, the AV should fire up as normal. Hold the back button for 3 sec and Android should appear on the top screen. You need to set the input to Aux for audio (more on that later). I put the unit under the AC duct in the centre console, with the wifi antenna on top of the AC duct near the shifter, the bluetooth antenna on the AC duct under the centre console The GPS unit on top of the DS to AC duct; they all seem to work OK there are are out of the way. Neat cable routing is a pain. For the drive recorder I mounted it near the rear view mirror and run the cable in the headlining, across the a pillar and then down the inside of the a pillar seal to the DS lower dash. From there it goes across and to one USB input for the unit. The second USB input is attached to the ECUtec OBD dongle and the 3rd goes to the USB bulkhead connected I added in the centre console. This is how the centre console looks "tidied" up Note I didn't install the provided speaker, didn't use the 2.5mm IPod in line or the piggyback loom for the Ipod or change any DIP switches; they seem to only be required if you need to use the Ipod input rather than the AUX input. That's it, install done, I'll follow up with a separate post on how the unit works, but in summary it retains all factory functions and inputs (so I still use my phone to the car for calls), reverse still works like factory etc.
    • Place the new daughterboard in the case and mount it using the 3 small black rivets provided, and reconnect the 3 factory ribbon cables to the new board Then, use the 3 piggyback cables from the daughterboard into the factory board on top (there are stand offs in the case to keep them apart. and remember to reconnect the antenna and rear cover fan wires. 1 screw to hold the motherboard in place. Before closing the case, make a hole in the sticker covering a hole in the case and run the cable for the android unit into the plug there. The video forgot this step, so did I, so will you probably. Then redo the 4 screws on back, 2 each top and bottom, 3 each side and put the 2 brackets back on.....all ready to go and not that tricky really.      
    • Onto the android unit. You need to remove the top screen because there is a daughterboard to put inside the case. Each side vent pops out from clips; start at the bottom and carefully remove upwards (use a trim remover tool to avoid breaking anything). Then the lower screen and controls come out, 4 screws, a couple of clips (including 3 flimsy ones at the top) and 3 plugs on the rear. Then the upper screen, 4 screws and a bunch of plugs and she is out. From there, remove the mounting brackets (2 screws each), 4 screws on the rear, 2 screws top and bottom and 3 screws holding in the small plates on each side. When you remove the back cover (tight fit), watch out for the power cable for the fan, I removed it so I could put the back aside. The mainboard is held in by 1 screw in the middle, 1 aerial at the top and 3 ribbon cables. If you've ever done any laptop stuff the ribbon cables are OK to work with, just pop up the retainer and they slide out. If you are not familiar just grab a 12 year old from an iphone factory, they will know how it works The case should now look like this:
    • Switching the console was tricky. First there were 6 screws to remove, and also the little adapter loom and its screws had to come out. Also don't forget to remove the 2 screws holding the central locking receiver. Then there are 4 clips on either side....these were very tight in this case and needed careful persuading with a long flat screw driver....some force required but not enough to break them...this was probably the fiddliest part of the whole job. In my case I needed both the wiring loom and the central locking receiver module to swap across to the new one. That was it for the console, so "assembly is the reverse of disassembly"
    • But first....while I was there, I also swapped across the centre console box for the other style where the AV inputs don't intrude into the (very limited !) space.  Part# was 96926-4GA0A, 284H3-4GA0B, 284H3-4GA0A. (I've already swapped the top 12v socket for a USB bulkhead in this pic, it fit the hole without modification:) Comparison of the 2: Basically to do the console you need to remove the DS and PS side console trim (they slide up and back, held in by clips only) Then remove the back half of the console top trim with the cupholders, pops up, all clips again but be careful at the front as it is pretty flimsy. Then slide the shifter boot down, remove the spring clip, loose it forever somewhere in the car the pull the shift knob off. Remove the tiny plastic piece on DS near "P" and use something thin and long (most screwdrivers won't fit) to push down the interlock and put the shifter down in D for space. There is one screw at the front, then the shifter surround and ashtray lift up. There are 3 or 4 plugs underneath and it is off. Next is the rear cover of the centre console; you need to open the console lid, pop off the trim covering the lid hinge and undo the 2rd screw from the driver's side (the rest all need to come out later so you can do them all now and remove the lid) Then the rear cover unclips (6 clips), start at the top with a trim tool pulling backwards. Once it is off there are 2 screws facing rearwards to remove (need a short phillips for these) and you are done with the rear of the console. There are 4 plugs at the A/V box to unclip Then there are 2 screws at the front of the console, and 2 clips (pull up and back) and the console will come out.
×
×
  • Create New...