Jump to content
SAU Community

GTR parts selling cheap~~~

TRIAL_GTR
 Share

Recommended Posts

TRIAL_GTR Contributor

TRIAL_GTR

Posted
Posted

i am selling my car as in standard form, so selling all the parts cheaps.

1. Apexi AX57 twin turbo with all briaded lines, just done 4000kms very good condition. cost me $7000 and i am asking $3800

2. Garrete N1 twin turbo with HKS actuator, only done 18000kms and good condition. cost me $5400. asking $2500......SOLD

3. HKS dump pipe mild steel. asking $200....SOLD

4. HKS twin front pipe stainless steel. asking $250....SOLD

5. HKS feul line without all fitting 10.5 mm. brand new never used. $200.....SOLD

6. Apexi Power Fc with hand controller. came off my skyline GTR R33 v-spec. in good condition with boost controller. asking $1300......SOLD

7. 2X 300zx AFM. asking $250 each.....SOLD

8. 2X recaro millinium seats. black coulor. very new. cost me $1100 each and i am asking for $400 swap over standard gtr seats.

9. TOMEI 600cc injector only done 4000kms. cost me $1200. asking $700.....SOLD

10. TOMEI 260 in/ex degree with 9.15 lift cams with Tomei Cam gear. only done 4000kms. cost me $1600 and i m asking only $800 the lot.......SOLD

11. DEFI gauges boost and exhaust temp. with the latest version of controller. black face. asking $600 the lot....SOLD

you guys can sms either on 0401625625 or email me on [email protected]. can provide pictures if requested

i am also selling my nissan skyline gtr r33 V-spec 1995. i am willing to let go at a reasonable price. the car got no accident before and cost $13000 of paint job as one of the show car coulor. the mods will be on my car now are

1. HKS forged pistons

2. Argo con rod

3. HKS 1.2 mm metal head gasket

4. NISMO full rebuild gaskets kit

5. JUN oil pump

6. TRUST valve springs

7. Intercooler

8. port and polised head

9. tein type ha shocks

10. enkei nto3 18" rims

11. HKS cat back exhaut systems.

12. EXedy single plate clutch with flywheel

the car just finish rebuild and in great condition, i will accept any reasonable price but i am asking for $40,000 for it and willing to trade car in. the price i am asking is a reasonable price. also can email me on [email protected] or sms on 0401625625. as all the picture to large. i need to send it to the mail.

Link to comment
https://www.sau.com.au/forums/topic/49621-gtr-parts-selling-cheap~~~/
Share on other sites

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now
 Share
Go to topic listing


  • Similar Content

  • Latest Posts

    • Kinkstaah
      WTB R34 GTR Guard Liners

      By Kinkstaah · Posted

      Ah! I actually managed to snag a lightly used set.... that aren't so suitable for me right now. They don't work on a GTT without some cutting or creative heat moulding. I thought about reselling them myself cause I didn't want to murder them, but it looks like I'm probably going to attempt to murder them/melt them because I may as well. @GTSBoy @PranK can somebody close this thread?
    • itsmeyo
      WTB R34 GTR Guard Liners

      By itsmeyo · Posted

      Hey mate,  I have a set, one is slightly damaged but wont be noticable once installed.  Shoot me a message if your still after them 
    • The Bogan
      NC MX5

      By The Bogan · Posted

      I couldn't wait But, the black constant tension hose clamps were too thick and there wasn't enough clearance at the T/B and I couldn't get it to seat properly, so I had use a silver one there I also added some 3" silicone over the alloy bit that goes through to hole on the radiator support as it looked like it was sitting on the edge of the hole in the radiator support, I never noticed a rattle or anything, but there was a witness mark It is basicly done, and I can live with the silver hose clamp at the T/B, I will get a black clamp for the head vent though where it is attached to the bulkhead fitting  It never stops...LOL, only issue now with the shock tower brace is it slightly touches the under bonnet liner now, if I leave it it will either wear some paint off the brace where it touches, or damage the liner, so I removed the liner to see what I have to work with, with the liner removed I have about 20mm of clearance, but sadly the middle part of the underside of the bonnet is only dusted with paint and looks crap, so I cannot have that, but.... as I have a roll of Carbuilders premium under bonnet insulation in the garage laying around that is only 5.5mm thick (we were going to use it on the boys Patrol, but he crashed the front of it a few months and it was written off, hence why he now drives my old Honda Accord Euro), I'll use the OEM liner as a template and get the Carbuilders stuff fitted up to cover that dusted paint up
    • Kinkstaah
      From Japan and back to Europe, my sh*tbox R34 GTT

      By Kinkstaah · Posted

      You have a knack for photography my friend. It makes the 86 look like a complete bucket. The 34 went with you to Europe and back. It's special. (we all feel the same about our 'shitboxes' that every bystander seems to absolutely love)
    • Dose Pipe Sutututu
      From Japan and back to Europe, my sh*tbox R34 GTT

      By Dose Pipe Sutututu · Posted

      LOL.... you are correct there.
×
×
  • Create New...