Jump to content
SAU Community

Recommended Posts

Gday,

Engine = RB25DET

Car = Cefiro

Limitations = Stock turbo

Considerations = Engine reliability

Goal = 200rwkw+.

Mod path 1

1. GTR intercooler

2. All air stuff (filter, dump, exhaust etc)

3. Apexi AVCR

4. Apexi SAFC (or SAFC II whatever the different is)

Mod path 2

1. GTR intercooler

2. All air stuff (filter, dump, exhaust etc)

3. Apexi PFC (no boost module)

4. two-stage boost controller solonoid thingy (cheapie)

This will be street car with occasional track/drift use.

I probably won't be upgrading turbos (if at all) for a long time. So the 1st path has the advantage of inital small outlay.

On the other hand the 2nd path has flexibility.

Which one is better and why/what for?

I guess what I wanna know is in the meantime (before getting bigger turbo, injectors etc) can the PFC justify the money in performance?

Thanks.

Link to comment
https://www.sau.com.au/forums/topic/50102-rb25-do-up-path/
Share on other sites

My 20 cents worth....

Mod path 1

3. Apexi AVCR

4. Apexi SAFC

This leaves you no way to adjust the ignition timing, this is bad for power production and reliability. You might get to 200 rwkw but that is simply max power. Without igntiion timing tuning, the average power will suffer as will response.

Mod path 2

3. Apexi PFC (no boost module)

4. two-stage boost controller solonoid thingy (cheapie)

The PFC allows you to adjust all of the ecu parameters, but the boost controller may compromise the reliability and response. If price is the consideration, then the Autospeed design (Norgren valves) boost controller is the go. Do a search there is plenty of data on why.

With just a cat back exhaust and a PFC (with Boost Control Kit) I have seen a couple of RB25's make ~200 rwkw. But regardless of what you do your are always living close to the edge with the ceramic turbine particularly if you are going to do some laps, sideways or not.

Hope that helps

Link to comment
https://www.sau.com.au/forums/topic/50102-rb25-do-up-path/#findComment-996873
Share on other sites

seems not too bad to me..

i wouldn't bother with the AVCR or S-AFC.. you'll only want the full ECU soon enough.

pickup a 2nd hand EBC (other than the overpriced Apexi) for around $350, or just stay with the bleeder I reckon until a bit later. Wouldn't worry too much about the turbo .. just get another when it breaks, you can go though a few before it starts getting expensive. Just maybe run lower boost and wrap the dump pipe to reduce outlet temps.

When my next car gets here, even $300 difference between the bleed valve and EBC I can keep thinking of a few extra things to spend the money on (i.e. some whiteline springs)

Link to comment
https://www.sau.com.au/forums/topic/50102-rb25-do-up-path/#findComment-996963
Share on other sites

Thanks guys.

Sounds like the PFC is the better bet. I've heard that the PFC boost controller module is not that good however and some people I've seen seem to be using the PFC and a AVCR. Is this just really high end stuff?

So the general consensus would be stay on the less push side of 12psi? I don't want to kill the turbo till I get an aftermarket one or upgraded one.

Mate i'd be happy to get a intercooler for $150 - Justjap said $650 for GTR cooler and micks metalcraft $1000 for pipes.

LOL thats total and utter garbage 'retail' prices but i hope it's not near what I'd be having to pay.

Other than getting custom FMIC pipes someone must make knock off cefiro pipes surely.

Okay. so PFC + boost controller module is circa $1500 i think. Plus tune.. hmm I'd say that's very much dependant on the availability of a cheap cooler.

Link to comment
https://www.sau.com.au/forums/topic/50102-rb25-do-up-path/#findComment-997449
Share on other sites

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now


  • Similar Content

  • Latest Posts

    • Yeah pretty impressive hey, good to see quality products not over-shooting their prices. That's what drew me to buy the hypergear turbo, just a shame I've never got the chance to see it in action
    • Thank you GTSBoy and MBS206 I have done the compression test with the motor out of the vehicle, reason for the test was to see if I needed to remove the head and do rings etc while its out. I'm in the process of respraying the vehicle and tidying up a few things. Story behind it all is I've just purchased the skyline and it was running when I got it, never drove it on the street though as I wanted to pull it down and do it all up again before registering it. the gentleman I purchased it from told me the motor has a forged bottom end and has a decent tune through it but I was going to pull the sump off anyway to see if it is a forged bottom end. that's why I thought id do a compression test beforehand. 
    • Man, I'm kind of amazed that the price of the turbo has not changed in 7 years. Everything else is inflating beyond reason, but not this? Good on Tao / hypergear I guess? Anyways, good luck with the sale!
    • I'm selling my brand new, in the box, never used Hypergear ATR45 - and I had some additions I paid for a few yrs back when I purchased it. Never ended up having the rest of the money to add all the mods at once, so I just ended up slowly selling each part. I originally had it internally gated, with the dump pipe, however I found it was incompatible with what I was going to use it for, so I contacted (I think Ken) from Hypergear, and he and I messaged back and forth & he got me to ship the turbo back, where they modified it & made it externally gated, and gave me the 5 bolt dump pipe attachment for custom welding. (Photos below) This turbo like I said has never touched the inside of an engine bay, it's completely brand new, never used, been sitting in the same box it arrived in, covered in plastic & all. Below are the photos of it: And while the guys at Hypergear were making it in-shop, they sent me some photos of the process: I'm looking at selling this just because I'm in need of the money right now, and don't have plans on modifying the 34 anytime soon - and from reviews & peformance sheets, this turbo had amazing results back when I was researching. The turbo was purchased in 2018 for $1.9k, with the mods I got added on. Looking at the website now, for the same turbo they sell (ATR45SAT), with the current addons it adds up to $1830 for the turbo Current addons included: - Bolted dump adaptor - Ball bearing CHRA - Braided oil feeding line So I'm looking to possibly sell it for around $1800, with shipping included in that 1.8k, It cost me around $120 to ship - so yeah thought I'd throw it out there and see if anyone was interested in purchasing. Cheers!
×
×
  • Create New...