Jump to content
SAU Community

Recommended Posts

Where is it located?

Can it be callibrated?

Mine seems to be about 4-5 degrees over all the time but it also gets some serious heatsoak from somewhere.

If the cars has been parked in the sun or even left in the garage after running then the outside temp reading can go into the 30's on a 10 degree day in Canberra! :flamed:

Link to comment
https://www.sau.com.au/forums/topic/50738-outside-temperature-sensor/
Share on other sites

mine is actually on the front where the air con fan is. on the top side of that there is a black thing with wires coming to the middle under the latch that you can un plug. don't know if you can change it but you could move it from there.

  • 2 years later...

So sorry to bring up an old thread but...

Ran an air conditioning diagnostic test and it comes up with a flashing 21. This means that the outside air temperature sensor is faulty or missing.

My ambient temperature is displayed as -30c.

I searched and searched on here but did not find a picture of said sensor. Many people have said it is located behind the front bar.

I found a plug with nothing connected to it, so one would assume this is the plug for this sensor. The sensor isn't there at all as far as I can see. It is a two pin plug, wire colours are light blue/white stripe and light green.

Does anyone know if this is the plug for the OAT sensor?

Thanks so much for your help. The plug that I found was in the location that the picture shows. The plug in the picture looks very similar to the one in my car also. The sensor is nowhere to be found, so I assume someone took it out in the past sometime.

I'll ring Nissan tomorrow to see if I can get a replacement sensor.

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now


  • Similar Content

  • Latest Posts

    • My apologies. I forgot we were talking about weird beard M series stuff. Had been talking elsewhere with someone about an R33 with similar subject and got confused.
    • Nope, I don't like the look of ND RF, or any ND really, I don't like their faces or arses, why, because of their "modern" lines, the NC, whilst "modernish" has a more rounded shape that I like Well, that's how my overly judgemental eyes see it anyway  
    • Should be more than fine, especially the overall fuel pressure would never exceed 3.5bar (assuming that thing never gets more than 0.5bar of boost in stock form). According to the chart, it's 11amps.
    • I definitely know the first rule here, look first, ask second. I've seen many people get roasted 😂 I found a few diagrams for the RB, but I'm yet to come across one for the VQ. From what I have read, the pump gets the +12v along with the FPCM, and it's the negative wire that gets passed through the resistor to regulate the voltage. So I assume I can just ground the negative wire at the pump to eliminate the FPCM control. But I really wanted to see the VQ circuit diagram first to make sure I understood it correctly. Once the new pump is in I'll do some testing to see how it behaves, and in the meantime, I'll keep looking for a wiring diagram. Thanks for your help mate, your time is greatly appreciated.    
    • Maybe? I have the Supercheap ToolPro low thingo. It has a somewhat smaller diameter lifting "bowl" than you would expect on a workshop grade trolley jack, and a split rubber pad to suit that diameter. It clears the "N1" style skirts I have. Probably wouldn't if the jack's bowl and a suitably larger rubber block were in use. Having said that though.....you only need the rubber block to exist on the inner side of the pinchweld, so could carve away any rubber that fouled the skirt, leaving some there for "insurance" </simples>
×
×
  • Create New...