Jump to content
SAU Community

Recommended Posts

Iputs more torque to front wheels, not sure of %age, but more than 50

Can't be more than 50%, ATTESSA hydraulic pump locks up the clucthes to the front wheels, rear wheels are always solidly connected. So at max pressure best is 50/50.

What does the centre diff button do next to the steering wheel?

Try it on wet grass. When turned off Stagea spins rear wheels for a bit and then feeds some torque to the front wheels and drives off. When turned on, it just drives off straight away, no waiting.

Very handy as the rear doesn't step out in the snow and ice. Not much use to me, no snow and ice in Sydney. Could be handy in the pits with the trailer on the back when it's wet though. The old Foulcan used to sit there spinning it's one rear wheel. Had to get towed to the sealed pit road once at Bathurst, very embarassing.

Just one more reason for choosing a Stagea :D

Link to comment
https://www.sau.com.au/forums/topic/51047-the-button/#findComment-1012070
Share on other sites

Hahahaha, good one SK, I can see it now, the old Foulcan smoking up one tyre in the pits and everyone looking thinking 'What the hell is he doing !!'...

Anyway, I just found this out last night as I was reading through heaps of Jap stuff on Stagea's.

With the button pressed in, the torque is 50/50 up to 20km/h. After 20km/h it sits at 80/20 (80% rear and 20% front) unless the front requires more, then it can vary up to 50/50.

Very interesting hay... You can see they were designed mainly for snow use (and would be great for pulling a boat out of the water at the boat ramp), and probably explains why you don't feel a big difference when driving normally with the button in.

J

Link to comment
https://www.sau.com.au/forums/topic/51047-the-button/#findComment-1012334
Share on other sites

jay do you know the addresses of the japanese sites you were looking at?

i searched google japan and yahoo japan and all the sites i keep finding are all the same stuff just the specs some pics of the guy/girls cars and mods etc...

looking for more interesting stuff like what you just posted

:D

Link to comment
https://www.sau.com.au/forums/topic/51047-the-button/#findComment-1012409
Share on other sites

jay do you know the addresses of the japanese sites you were looking at?

I actually got the link from Rezz's post on the thread you started :D The first link, but it was in a link in that link - if that makes sense !!!

Here's the first link;

http://homepage2.nifty.com/WGNC34/tuningdatetop.htm

You have to click on 'INDEX' for it to bring down a list of other links.

That particular info is the third link down in that link :) - here's the link;

http://homepage2.nifty.com/WGNC34/tuningdouryoku.htm

To read it you have to put it into a translator (bablefish won't work for some reason....). I use this translator http://www.systransoft.com/ after a while you have to register, but it's free.

Then in some sort of Japglish you can make this out at the bottom of the page;

"You handle for the reference and there is this kind of statement in the instruction manual.

At the time (usually time) of synchronizer mode OFF basis: 0: 100 MAX50: Variable control up to 50

At the time of synchronizer mode ON below (when departing) vehicle speed 20 km... 50: 50 fixing

Above (when travelling) vehicle speed 20 km... basis 20: 80 MAX50: Variable control up to 50."

J

Link to comment
https://www.sau.com.au/forums/topic/51047-the-button/#findComment-1012661
Share on other sites

good stuff jay thanks for the info

am trying to get my stagea site uploaded in the next couple of days

yeah babelfish is crappy i will try the systransoft program and see how i go :D

prank

good idea can you start one and maybe put the dash removal tutorial that shan posted a while back in there and sticky it??

:)

Link to comment
https://www.sau.com.au/forums/topic/51047-the-button/#findComment-1012693
Share on other sites

so this is a good feature to have when chopping holden utes at the traffic lights in the rain?

:);) ;)

Mate he was soooooo far behind, I leasurely changed lanes and drove along at the speed limit. Still took him a K or so to catch up. Subaru Forresters are also fun, they keep looking in the rear view mirror wondering why this strange waggon is keeping up. KEEPING UP, huh I was looking for room to go around. And then there was 4 guys in 2 WRX's that got whiplash when I went in between them in a roll on at the lights.

I have been having so much fun. :D

Link to comment
https://www.sau.com.au/forums/topic/51047-the-button/#findComment-1012695
Share on other sites

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now


  • Similar Content

  • Latest Posts

    • Have a look at that (shitty) pic I posted. You can see AN -4 braided line coming to a -4 to 1/8 BSPT adapter, into a 1/8 BSPT T piece. The Haltech pressure sender is screwed into the long arm of the sender and factory sender (pre your pic) into the T side. You can also see the cable tie holding the whole contraption in place. Is it better than mounting the sender direct to your engine fitting......yes because it removes that vibration as the engine revs out 50 times every lap and that factory sender is pretty big. Is it necessary for you......well I've got no idea, I just don't like something important failing twice so over-engineer it to the moon!
    • Yup. You can get creative and make a sort of "bracket" with cable ties. Put 2 around the sender with a third passing underneath them strapped down against the sender. Then that third one is able to be passed through some hole at right angles to the orientation of the sender. Or some variation on the theme. Yes.... ummm, with caveats? I mean, the sender is BSP and you would likely have AN stuff on the hose, so yes, there would be the adapter you mention. But the block end will either be 1/8 NPT if that thread is still OK in there, or you can drill and tap it out to 1/4 BSP or NPT and use appropriate adapter there. As it stands, your mention of 1/8 BSPT male seems... wrong for the 1/8 NPT female it has to go into. The hose will be better, because even with the bush, the mass of the sender will be "hanging" off a hard threaded connection and will add some stress/strain to that. It might fail in the future. The hose eliminates almost all such risk - but adds in several more threaded connections to leak from! It really should be tapered, but it looks very long in that photo with no taper visible. If you have it in hand you should be able to see if it tapered or not. There technically is no possibility of a mechanical seal with a parallel male in a parallel female, so it is hard to believe that it is parallel male, but weirder things have happened. Maybe it's meant to seat on some surface when screwed in on the original installation? Anyway, at that thread size, parallel in parallel, with tape and goop, will seal just fine.
    • How do you propose I cable tie this: To something securely? Is it really just a case of finding a couple of holes and ziptying it there so it never goes flying or starts dangling around, more or less? Then run a 1/8 BSP Female to [hose adapter of choice?/AN?] and then the opposing fitting at the bush-into-oil-block end? being the hose-into-realistically likely a 1/8 BSPT male) Is this going to provide any real benefit over using a stainless/steel 1/4 to 1/8 BSPT reducing bush? I am making the assumption the OEM sender is BSPT not BSPP/BSP
    • I fashioned a ramp out of a couple of pieces of 140x35 lumber, to get the bumper up slightly, and then one of these is what I use
    • I wouldn't worry about dissimilar metal corrosion, should you just buy/make a steel replacement. There will be thread tape and sealant compound between the metals. The few little spots where they touch each other will be deep inside the joint, unable to get wet. And the alloy block is much much larger than a small steel fitting, so there is plenty of "sacrificial" capacity there. Any bush you put in there will be dissimilar anyway. Either steel or brass. Maybe stainless. All of them are different to the other parts in the chain. But what I said above still applies.
×
×
  • Create New...