Jump to content
SAU Community

Recommended Posts

its probably just your switch, take the door panel off and find the motor that drives the window panel. use a 9V battery and wire it to the two wires going into it. if you put it the right way, the window will go up, if you put it the other way the window will go down. SHould solve your problem till you replace the switch.

Link to comment
https://www.sau.com.au/forums/topic/51140-help/#findComment-1013405
Share on other sites

did u read my post in the other thread?

have a listen carefully to the motor...once an a while it will actually turn over but shit itself again. when u hear it turn over quickly push the window up from inside the door trim with ur hands or pull it up if it is sticking out of the top. thats how i did mine.

other than that do what chop's did disasemble and take the motor out and put some wood in there.

Link to comment
https://www.sau.com.au/forums/topic/51140-help/#findComment-1013408
Share on other sites

is the window fully down? my window has problems going up aswell, however it always goes down fine. With my window if i take it down say half way, and it doesn't want to go back up again, i hit the top of the window down while holding the switch and it comes back up again. If your window is fully down take off the door trim, get a thin bit of wood or something u can stick down the door onto the top of the window, hold the window switch to bring the window back up and tap down on the window. see if it works.

i can't actually hear mah motor shit itself!!!
Link to comment
https://www.sau.com.au/forums/topic/51140-help/#findComment-1013429
Share on other sites

im pretty sure its ur switch thats faulty mate.....replace the switch or do wat funkeymonkey said

what ive done before in other cars is replace the switch with the passanger side switch momentarily just to move the window up. I dont know if it will work though since the driver side console has a few buttons there and thus the passanger side switch may not fit

Link to comment
https://www.sau.com.au/forums/topic/51140-help/#findComment-1013491
Share on other sites

just remember if its done it once it'll most probably do it again. like when i went to the shops and i accidentaly pressed the switch it went down 2cm but not back up again so i had to go home:D:D theres no way im gonna leave my car with my windows slightly open in springvale:D:D

Link to comment
https://www.sau.com.au/forums/topic/51140-help/#findComment-1015070
Share on other sites

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now


  • Similar Content

  • Latest Posts

    • Ok thanks..that was my second question if i can somehow bypass this even with Nistune(that is all i have right now...aparat from stock ECU. So with some aftemarket it can by "bypassed" or make it work?  I know there is Link or Haltech (mainly used). We have ECUmaster here so i will gather some info about it.
    • Yes. You will need to get the original boost sensor and wire it in. That is.... if you plan to use a stock ECU - even a Nistuned ECU. The Nissan ECU will not operate correctly without it connected. And yes, it will do annoying stuff like you are experiencing. You will almost certainly be better off with some aftermarket ECU, than trying to hunt down rare sensors.
    • Ok so ABS/TCS is "not" the problem. Yeah i know now about the ABS with Nistune(i told that to the Nistune guy) but iam not 100% why or why i dont have ABS. ABS cube is in the engine (always has been) but i had braked couple of times rly hard and brakes just locked and scream. Does all Skylines have ABS cube? That boost sensor https://www.sau.com.au/forums/topic/367633-wtb-r34-gtt-turbo-pressure-sensor-pics-inside/ Is this it? I need to ask but i have a picture of engine bay and i do not see that (100% is not in that place) If i do not have this the car can do what mine is?(cutting around 4000 rpm) Here is the pic of my engine bay(only one i have) BUT i think i dont have that cuz loom was used from my RB20DE NEO and i know (obviously) that it does not have boost control or any wire to that...) so maybe that is the problem? (i dont know for 100% if that car where the engine is from had that)...but i dont have the loom from that
    • I'm with you here. It's either loom has an issue, OR, injectors are not functioning properly. It could even be they're just constantly dribbling, hence the wet, but not firing.
    • Depending on how long the car sat it is very possible for injectors to be stuck open or closed, I'd get them cleaned and flow tested. Other than that, obviously when the loom changes and the car doesn't start any more....the loom is suspect so some tracing / comparing may be required
×
×
  • Create New...