Jump to content
SAU Community

Fitting 550cc Supra 2jz turbo injectors into a RB25det


Recommended Posts

Guest darrinspencer

I am looking into the "posibility" of fitting Toyota Supra IV twin turbo USA spec 550cc injectors into a RB25det.

Japanese spec are 480cc.

The injectors are low impedence, but RB25 use high impendence

Is there some way of re-wiring etc to get these to work?

Will they fit into the fuel rail with little to no mods?

I have a new Wolf plug-in ecu, which is not fitted yet, will this be able to run low impedence injectors instead of high impedence?

These injectors can be found for about $150 aust., hense the consideration in finding out if these will work

Has anyone tried these?

Attached is a photo of what they look like the blue set of six

Also attached is a photo of nismo 555cc injectors, just to compare

Dunno if they would fit, they look alot like RB25 injectors though

If they are low impedence, you could wire in a GTR resistor pack and it should work fine

Chris

Guest darrinspencer
They look too large at the base to fit in the RB25 rail. Have you looked into 550cc 20B cosmo injectors?

I have, but they are hard to get and are nearly as dear as buying s/hand Sard etc rb25 injectors, also the WRX boys want them

Yes they will fit with a little effort and the wolf Plug in will drive them with no problem with out any need for a resitor. If you have any doubts email Wolf in Australia and say Steve thomas from SST told you the wolf will drive these injectors.

So are you using these in a RB25det?

If you are, what was needed to make these work.

Steve- thanks for the answer.

I'm using these in an RB30DET with the R33 head. I machined up some aluminum collars to locate them centrally in the bowl. A small amount of material needs to be removed from the bottom filter cage and aluminium tip so they will fit into the bottom of the bowl. Plugs are different. Rather than "cut and shut", i bought new terminals and plugs and re-crimped them.

They are high impedance (13 ohms i think).

Guest darrinspencer
I'm using these in an RB30DET with the R33 head. I machined up some aluminum collars to locate them centrally in the bowl. A small amount of material needs to be removed from the bottom filter cage and aluminium tip so they will fit into the bottom of the bowl. Plugs are different. Rather than "cut and shut", i bought new terminals and plugs and re-crimped them.

They are high impedance (13 ohms i think).

The US spec are low impedance.

What computer are you running?

I think we have a communication breakdown here.....

To clarify, I have 20B cosmo injectors which i sourced from dysons and a rotary forum. These are high impedance. I machined up collars to fit these in the r33 rail as i mentioned above. Computer is Haltech E11.

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now


  • Similar Content

  • Latest Posts

    • It is a kunfine Android screen . Does anyone know the wirering diagram of the fuga ??
    • just an update to this, poor man pays twice  Tried sanding down the pulleys but it didnt do the trick. Chucked another second hand alternator in the na car which I got for free off my mate and its fixed the squelling. Must have been unlucky with the bearings.    As for my turbo car, I managed to pick up a cwc rb alternator conversion bracket + LS alternator for 250 off marketplace, looked to be in really good nick. Installed it , started the car and its not charging the battery.... ( Im not good with auto elec stuff so im not sure if this was all I needed to do but I verified such by using a multimeter on the battery when the engine was running and I was only getting 12.2v )   I had to modify the earth strap for the new LS alternator , factory earth strap was a 10mm bolt which did not fit the bolt on the LS alternator which was double the size so I cut it off , went to repco bought some ring terminals that fit, crimped it onto the old earth strap and bolted it up to the alternator , started the car and same issue. Ran like shit and was reading 12.2 at the battery.  For a "plug and play" advertised kit thats not very plug and play but alas.  My question is , am I missing something ? Ive been reading that some people recommend upgrading the stock 80 amp alternator fuse to a 140 amp but I dont see how that would stop the alternator charging especially at idle not under load.  Regardless ive pulled it out and am going to get it bench tested by an auto elec tomorrow but it would be handy to know if ive missed something silly or have done something wrong.   
    • My wild guess is that you have popped off an intake pipe....check all of the hoses between the turbo and the throttle for splits or loose clamps.
    • Awesome, thanks for sharing!
    • To provide more specific help, more information is needed. What Android screen? What is its wiring diagram? Does the car's wiring have power at any required BAT and ACC wires, and is the loom's earth good?
×
×
  • Create New...