Jump to content
SAU Community

Recommended Posts

Hi,

I'm considering a job in Japan for next year, and wondering what's involved in bringing a car back with me to Australia that I would buy over there?

I'm aware that I'd need to have proof of ownership for 12 months or greater, but I'm unsure of how the process differs from the Low Volume Import scheme. Apart from not needing the same type of compliance as a Low Volume import, what other differences are there?

Would the car need to be registered and used, or could it be bought at the beginning of the year, warehoused, and then import as a private import?

Thanks for any info you can provide.

-wm

Link to comment
https://www.sau.com.au/forums/topic/5394-private-import/
Share on other sites

I have heard rumours that if you have owned the car for over 12 months living in Japan it can be bought over as a private import and thus does not have t comply with ADR's as not part of the low volume import category.

This would be quite cool indeed.

:uh-huh:

Link to comment
https://www.sau.com.au/forums/topic/5394-private-import/#findComment-82377
Share on other sites

Guest GR33DyMANGO

so BY BY you're saying u dont have to pay for compliance with costs a few grand and is increasing in march 2003 to something rediculous so its too costly to import???

that would be so awesome if thats what u mean. i might be heading off to hong kong in about a year to work. hmmm.. maybe i could have an r35 in a few years... hehee....

Link to comment
https://www.sau.com.au/forums/topic/5394-private-import/#findComment-82398
Share on other sites

to be eligible for personal import you need to supply the following..... Parking permit,registration documents in your name,Insurance documents,passport(stating that you have been in a particular country for over 12mnths).Once an impot approval has been issued,you can send the car.Once it arrives the car will need to be checked by an engineer.Seatbelts will need to be changed if they dont have an e marking,child restraints be fitted,unleaded filler neck and some other stuff depending on the model of the vehicle.In regards to a car from hk...id forget about it as the tax payable on buying a car and owning it for a year in hk would out way the cost of just buying it straight from japan...especially a model such as a new 2 door skyline which will be eligible under the new sevs scheme anyway.....hope this helps

Link to comment
https://www.sau.com.au/forums/topic/5394-private-import/#findComment-82457
Share on other sites

yep....the same duty applies...although i beleive there is a depreciation form that you can fill out but its not woth the hassle...unless you owned the car for 5 years..then the purchase price would be dearer than the current market price.I got pics but how do you post them to apare on the screen and not as an attachement???

Link to comment
https://www.sau.com.au/forums/topic/5394-private-import/#findComment-82501
Share on other sites

Yo Waxman, I'm considering going to Japan next year aswell.....

You gonna be teaching english over there or doing something else?

Keep us all informed of how everything pans out for you.......I'm sure that if you go over you'll have no spare time because you'll be too busy finding cheap parts for everyone here! :lol:

Link to comment
https://www.sau.com.au/forums/topic/5394-private-import/#findComment-82551
Share on other sites

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now


  • Similar Content

  • Latest Posts

    • It says 300ZX, does that make it an Aus delivered car? Funny how back in the day I just couldn't care less about Z32's and these days I am just in love with them. Back when Nissan was into pushing the envelope. 🤣
    • Hi guys, just after some guidance with an R34 sunroof that has stopped working correctly. It still opens and closes perfectly fine, but it no longer tilts/vents up or down. As a result, the rear of the glass now sags a bit as it drops down slightly in order to retract into the roof, but now it can't pop upwards into a flush position. I’ve probed the pins on the back of the switch connector with a multimeter and it seems like both switches (for open/close and tilt/vent) still work correctly. Any ideas on what it could be, or where I should even start in terms of diagnosing? I'm sure someone's had this issue before but I haven't been able to find anything online relating to this specific issue, most of the issues are with the seals leaking or the motor failing entirely. Thanks in advance!
    • Do you have some data like fuel pressure? It's really hard to say if you're still fighting a fuel system issue at this point. Could be something weird like the FPCM dipping out.
    • Yeah in that case, pulling the dent out. Event a very slight dent can create a lot of work filler-wise and there is a strong chance the panel won't be the factory shape when you are done (as the dent will result in a new high point created somewhere, then everything is brought up to that new high point... but the panel shouldn't be that high if that makes sense).  So you've filled and primed the panel and it is flat, why would you go back and remove the primer and add more filler? 
    • Something else I have been faffing with while the car was off the road is making the AC work. Assuming the car isn't at a thermal limit the idea of having AC while waiting in line to go on track sounds delightful. I have actually been lugging around the weight of the entire system since 2018 when the RB25NEO went in without it working at all.  The main reason was in the first few events before I got around to re-gassing it the rubber hose that runs under the manifold had the factory heat wrap/sleeve fail resulting in this: ~2 years ago I purchased a complete used R32 AC line set but when I finally went to install it the line i needed was different where the expansion section is I found a local place that was able to replace the rubber section and re-crimp. They also added some modern heat sleeve to the hose Tight fit but fingers crossed this is the last physical piece of the puzzle needed
×
×
  • Create New...