Jump to content
SAU Community

Recommended Posts

Hey

got a couple sets of H-Beam 6" SJ rods for sale if people r interseted

they r 4340 steel and come wit ARP rod bolts

the will handle bout 1000hp if tuned correctly

i want $800 per set for them

they will fit n rb30 wit some machining

let me know

regards

Troy

Link to comment
https://www.sau.com.au/forums/topic/54506-eoi-eagle-h-beam-rods/
Share on other sites

ill find out if they can fit n rb25

id say no as it has a shorter stroke than the rb30 but if the 5.7" can fit then i can get them aswell

but ill find out for certain

not sure if they r lighter than stocks bu they can handle roughly 850-1000hp when tuned correctly

cheers

Troy

they wont fit anything except rb30's and if they are still chev ones they still require extensive mods to fit a rb30. Oh and they are heavier than stock rods, check my posts in the the r33 rb30det conversion thread just use my name and eagle rods in a search of the thread!!!

Hey Troy,

can you please tell me what exactly needs to be machined to make them fit in an RB30 bottom end? I am doing and RB30 conversion for my R33 and was initially going to settle with preparing my standard rods. However, if I can get H beam rods with ARP bolts for similar money...

Thanks in advance,

Adrian

yes the 6" will only fit rb30

lik i hav stated, some machinig is needed

not much $ needs to b spent tho

and as i said, order pistons to suit, will save in machin cost

hey mate

will u b ordering pistons aswell?

if u r then i would suggest CP pistons as they are damn good quality n damn good price

if u dont order pistons to suit the pin size of the rod which is 0.927" then u will hav to get it bushed so that it fits the pistons

u will also need to get the sides of the rods linished so that they fit down the bore, id advise to bore the block 20thou so the rods dont need much linishing

then u will hav to get the rods fitted to the crank which involves a little bit of machining

if u order your pistons to suit then u will b lookin at bout $200 i hav been told to get the rods fitted to the crank

if u want a set then ill do them a bit cheaper

cheers

Troy

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now


  • Similar Content

  • Latest Posts

    • How dare you sell your unreliable Skyline and buy a reliable, Toyota/Yamaha car with a strong gearbox, torsen LSD and Toyota reliability. At least you won't need to worry about oil pumps, big catch can, oil restrictors, blowing off power steering belts, sheering off 3rd gear, failing ABS relays/pumps, etc.
    • Hope you aren't too sore after that one, might take a day or 2 to notice yet and I guess it is a loooooong drive home. On the bright side, tube frame front end is a thing at superlap, right?
    • https://www.facebook.com/share/p/18rmVb1SKB/ 
    • The chart of front pressure to rear pressure (with one being on the x axis and the other being on the y axis) is not a straight line on a typical proportioning valve. At lower pressures there is a straight line with one slope, and at higher pressures that changes to a lower slope. That creates a bend in the line at that pressure, called the knee point. If you do not change the proportionng as the pressure gets higher, you will suffer excessive pressure (at one end of the car or the other, depending on which way you look at the proportioning action) and then get lockups at that end. The HFM BM57, from my memory of previous discussions, is based on the BM57 from a different car (to a Skyline), with a different requirement for the location of the knee point and the distribution of pressure front to rear, and so is not a good choice for an upgrade on a Skyline. Here's a couple of links to some old posts, one from here, one from elsewhere. A lot of it pertains to adjustable prop valves, but the idea is the same. There are plenty of discussions on here about this issue from al the many years of people wanting a cheap/accessible option. https://grassrootsmotorsports.com/forum/grm/learn-me-brake-proportioning-valves/236880/page1/ https://grassrootsmotorsports.com/forum/grm/learn-me-brake-proportioning-valves/236880/page1/  
    • Yeah dunno why johhny posted that here with no context, just post on FB/insta bro where he put it up?  Laine had an off at T4 during Thurs prac, he's ok, car is less than perfect, they are done for the weekend, he can fill in the rest. Bando also binned it like 100m up the road.   
×
×
  • Create New...