Jump to content
SAU Community

Recommended Posts

kit is an original BN Sports... cost... well retails for 273,000 Yen, which is $3300 by todays exchange rate, plus shipping n all that.

For the AE86... bought 4L of canary yellow acryllic, 4L of thinners and 4L of prepwash n 4L of clear today for $320... time to paint up the engine bay and put all the parts in. Bought a S13 cradle (control arms, suspension, steering rack etc) for $500 as well. costs are starting to add up now :)

  • Replies 154
  • Created
  • Last Reply

Top Posters In This Topic

they always do.....

um up to about $12K on the line in the last 6 months :) ooh well should go hard.

thats pretty damn cheap for paint.. but its only acryllic .. why not go for 2 pak paint? but then again your already on the costs.

our AE is almost ready for painting.. been undercoated and is still halfway through the rub back... still reckon at least a month til its done....

im in the search at the moment for an ae86, with fuel pricers rising the skyline becomes more and more a weekend only car.

i've always been a fan of the ae86, my mate has own 3; aus levin with 4ac then aus levin with 4age swap and now he has a jap ae85 tureno coupe.

i just want to find myself a nice clean ae86 i really like the tureno soo its going to be soo hard to find one cheap, i might just end up getting aus spec levin and going a 20v swap and put some quads on it

im in the search at the moment for an ae86, with fuel pricers rising the skyline becomes more and more a weekend only car.

i've always been a fan of the ae86, my mate has own 3; aus levin with 4ac then aus levin with 4age swap and now he has a jap ae85 tureno coupe.

i just want to find myself a nice clean ae86 i really like the tureno soo its going to be soo hard to find one cheap, i might just end up getting aus spec levin and going a 20v swap and put some quads on it

thats still a popular mod in Japan... just get the black top 20v as it has more power std than the silver top.

That's actually a mate's car that's being race-prepped (sitting next to my AE86), which I tried the kit on as it already had all the panels off. Its got a full cage in it (only half of it in while we redo the wiring in the car).

I can get em from Japan, but as I said, they're not cheap ;)

my mates car. i have more recent photos of it but i am in the us on my laptop so this is all i have

nice...

where abouts did he get the rear wing??? and how much?

and how did it get attached ... we wanna put it on the sprinter.. but need to get one and figure out the attachment before we continue the prepping.

got some info on the weekend....

found a sprinter coming into the country in a couple of weeks..

4AGE..20V with HKS cams

coilovers

mech LSD

BRIDE buckets...

have to have a look at it once she comes in.. but im pretty sure i'll get it!

Avi, his website's http://www.jap.com.au tell him Shan from j-spec sent ya and he might cut you a deal... or not... his username's a_v_i on most forums (SAU and NS included).

http://www.jap.com.au/ae86.html

oh and I have a "JDM tyte" AE86 front grille (the clear one with spaces for foggies... think they're called letterbox style or something) for sale too... and a whole heap of interior bits and pieces and a set of trueno headlights with motor assemblies.

  • 2 weeks later...

how long you been at j-spec for shan???

always looking at that site for nice bargain :D

that convert silvia looked good the other day...

my mate just got import approval for his s6 rx7 race car he got through you guys ... cant wait til it comes into the country :P

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now



  • Similar Content

  • Latest Posts

    • Hi, is the HKS  Tower Bar still available ? negotiable ? 🤔
    • From there, it is really just test and assemble. Plug the adapter cables from the unit into the back of the screen, then the other side to the car harness. Don't forget all the other plugs too! Run the cables behind the unit and screw it back into place (4 screws) and you should now have 3 cables to run from the top screen to the android unit. I ran them along the DS of the other AV units in the gap between their backets and the console, and used some corrugated tubing on the sharp edges of the bracket so the wires were safe. Plug the centre console and lower screen in temporarily and turn the car to ACC, the AV should fire up as normal. Hold the back button for 3 sec and Android should appear on the top screen. You need to set the input to Aux for audio (more on that later). I put the unit under the AC duct in the centre console, with the wifi antenna on top of the AC duct near the shifter, the bluetooth antenna on the AC duct under the centre console The GPS unit on top of the DS to AC duct; they all seem to work OK there are are out of the way. Neat cable routing is a pain. For the drive recorder I mounted it near the rear view mirror and run the cable in the headlining, across the a pillar and then down the inside of the a pillar seal to the DS lower dash. From there it goes across and to one USB input for the unit. The second USB input is attached to the ECUtec OBD dongle and the 3rd goes to the USB bulkhead connected I added in the centre console. This is how the centre console looks "tidied" up Note I didn't install the provided speaker, didn't use the 2.5mm IPod in line or the piggyback loom for the Ipod or change any DIP switches; they seem to only be required if you need to use the Ipod input rather than the AUX input. That's it, install done, I'll follow up with a separate post on how the unit works, but in summary it retains all factory functions and inputs (so I still use my phone to the car for calls), reverse still works like factory etc.
    • Place the new daughterboard in the case and mount it using the 3 small black rivets provided, and reconnect the 3 factory ribbon cables to the new board Then, use the 3 piggyback cables from the daughterboard into the factory board on top (there are stand offs in the case to keep them apart. and remember to reconnect the antenna and rear cover fan wires. 1 screw to hold the motherboard in place. Before closing the case, make a hole in the sticker covering a hole in the case and run the cable for the android unit into the plug there. The video forgot this step, so did I, so will you probably. Then redo the 4 screws on back, 2 each top and bottom, 3 each side and put the 2 brackets back on.....all ready to go and not that tricky really.      
    • Onto the android unit. You need to remove the top screen because there is a daughterboard to put inside the case. Each side vent pops out from clips; start at the bottom and carefully remove upwards (use a trim remover tool to avoid breaking anything). Then the lower screen and controls come out, 4 screws, a couple of clips (including 3 flimsy ones at the top) and 3 plugs on the rear. Then the upper screen, 4 screws and a bunch of plugs and she is out. From there, remove the mounting brackets (2 screws each), 4 screws on the rear, 2 screws top and bottom and 3 screws holding in the small plates on each side. When you remove the back cover (tight fit), watch out for the power cable for the fan, I removed it so I could put the back aside. The mainboard is held in by 1 screw in the middle, 1 aerial at the top and 3 ribbon cables. If you've ever done any laptop stuff the ribbon cables are OK to work with, just pop up the retainer and they slide out. If you are not familiar just grab a 12 year old from an iphone factory, they will know how it works The case should now look like this:
    • Switching the console was tricky. First there were 6 screws to remove, and also the little adapter loom and its screws had to come out. Also don't forget to remove the 2 screws holding the central locking receiver. Then there are 4 clips on either side....these were very tight in this case and needed careful persuading with a long flat screw driver....some force required but not enough to break them...this was probably the fiddliest part of the whole job. In my case I needed both the wiring loom and the central locking receiver module to swap across to the new one. That was it for the console, so "assembly is the reverse of disassembly"
×
×
  • Create New...