Jump to content
SAU Community

Recommended Posts

CLEAN YOUR INJECTORS!!!!!!!!!

i just pulled mine out today, the car was running fine but i decided to replace them with a set i just had cleaned to be on the safe side.

when i pulled out the fuel rail i got a nasty suprise. The caps on the end were cracked and the injectors were full of gunk. after flowtesting them 1 was down to 250!!! and 2 were 255. when they should all be 270.

the new set i put in flowed at 285 each.

the responsiveness it much better.

if i didnt replace them the car could have leaned out and gone bang...

if you have bought a car and not had them tested yet it only takes 1 hour to take em out and 1 hour to have em cleaned and an hour to put them back in. you dont know what condition one of the most important things for keeping your engine safe are in.

you wouldnt drive without oil would you?

CLEAN YOUR INJECTORS PEOPLE!!!

here is a quick guide

1.you need to remove 2 bolts one on the front and one on the back of the fuel rail.

2. remove the fuel supply and retiur lines from the rail/regulator assembly

3. remove the bolt from the bracket that supports the rail at front under regulator

4. remove injector clips, i did this with tiny long nose pliers, then unplug all the injectors. dont worry about marking them they are all labled.

5. you can now wiggle the fuel rail out about 40mm. you need to take out injector 5 and 6 to get the rail out from under the plenum.

slide the rail out and check the grommets are NOT on the injector bottoms over the pintle cap. make sure there is a grommet in every hole in the plenum.

wiggle out the injectors from the fuel rail. put them in a clean plastic container and take them to cleaning place.

PUTTING EM BACK IN...

when putting injectors in the rail be very careful to push evenly as not to squash the o rings.

put in injector 1, 2, 3, 4 Slide the rail back in place.

once in place replace injector 5 and 6. this is quite hard.

PLUGS!

injector 6 comes from the main harness. injector 5 comes from the wires on the fuel rail and 4, 3, 2, 1 cone from the injector harness and are labled. replace all the clips.

push the injerctors into holes in plenum and bolt the rail in place.

connect up the fuel supply and return lines and bolt the bracket back into place.

repressurise the rail by turning the car back to "on" check for leaks...

drink cold beer and tell your mates how cool you are cause you fix your own car:)

Link to comment
https://www.sau.com.au/forums/topic/54531-injector-cleaning/
Share on other sites

you got any tips on getting em out ...

once my new ones are clean, gonna have to do this, and it doesn't look like a 2 hour job if you have to take the plenum off ....

CLEAN YOUR INJECTORS!!!!!!!!!

i just pulled mine out today, the car was running fine but i decided to replace them with a set i just had cleaned to be on the safe side.

when i pulled out the fuel rail i got a  nasty suprise. The caps on the end were cracked and the injectors were full of gunk. after flowtesting them 1 was down to 250!!! and 2 were 255. when they should all be 270.  

the new set i put in flowed at 285 each.

the responsiveness it much better.

if i didnt replace them the car could have leaned out and gone bang...

if you have bought a car and not had them tested yet it only takes 1 hour to take em out and 1 hour to have em cleaned and an hour to put them back in. you dont know what condition one of the most important things for keeping your engine safe are in.

you wouldnt drive without oil would you?

CLEAN YOUR INJECTORS PEOPLE!!!

oooh, i dont envy you they are a bitch to take out on the rb25...

on the rb20 its just the 2 bolts that hold on the fuel rail, 2 fuel lines, injector plugs and the master feed injector power line. you dont need to take the plenum off :)

here is a pic for those of you who are not scared.

injektaz.JPG:D:(:D

Actually, Nathan @ Grey Imports mentioned this to me but yesterday: to quote him "get your injectors cleaned because you loose a lot of power if they're dirty".

It might also be worthwhile buying a couple of "rebuild kits" (ie kits that contain the little rubber seals).

LW.

Hell How many miles had your car covered, i just changed my standard injectors to gtr ones and the old ones were in superb condition, my car has only done 100,000km, :)

If rb25 injectors are worse than rb20 then you are really going to have fun i struggled with my rb20 ones. :D

Nathan

Actually, Nathan @ Grey Imports mentioned this to me but yesterday: to quote him "get your injectors cleaned because you loose a lot of power if they're dirty".

It might also be worthwhile buying a couple of "rebuild kits" (ie kits that contain the little rubber seals).

LW.

Nathan cleaned mine for me, he has a nifty machine that does the job.

take it to him he is in Annandale.

took about an hour to get em cleaned and he is a very freindly guy full of good advice. He cleaned mine for $120. depending on the condition/type they might be more.

I am hopeless writing guides so i cant help there much.

1.you need to remove 2 bolts one on the front and one on the back of the fuel rail.

2. remove the fuel supply and retiur lines from the rail/regulator assembly

3. remove the bolt from the bracket that supports the rail at front under regulator

4. remove injector clips, i did this with tiny long nose pliers, then unplug all the injectors. dont worry about marking them they are all labled.

5. you can now wiggle the fuel rail out about 40mm. you need to take out injector 5 and 6 to get the rail out from under the plenum.

slide the rail out and check the grommets are NOT on the injector bottoms over the pintle cap. make sure there is a grommet in every hole in the plenum.

wiggle out the injectors from the fuel rail. put them in a clean plastic container and take them to cleaning place.

PUTTING EM BACK IN...

when putting injectors in the rail be very careful to push evenly as not to squash the o rings.

put in injector 1, 2, 3, 4 Slide the rail back in place.

once in place replace injector 5 and 6. this is quite hard.

PLUGS!

injector 6 comes from the main harness. injector 5 comes from the wires on the fuel rail and 4, 3, 2, 1 cone from the injector harness and are labled. replace all the clips.

push the injerctors into holes in plenum and bolt the rail in place.

connect up the fuel supply and return lines and bolt the bracket back into place.

repressurise the rail by turning the car back to "on" check for leaks...

drink cold beer and tell your mates how cool you are cause you fix your own car:)

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now


  • Similar Content

  • Latest Posts

    • Food for thought, the stock oil filter thread is a 3/4-16 UNF, which has an ID of about 10 to 12mm (according to ChatGPT lol). Now compare than to an 10AN, which has an ID of about 14mm (Raceworks is 14.2mm, Speed flow is 14.27mm).  
    • Yep, totally get that. However hooking in for Generator back up is only a few hundred bucks for the wiring. You could put a couple of those in (for different circuits explicitly) and run a couple of baby generators. Bonus, you can balance them across different circuits, and now have backups in your backup. I'm looking at buying places that won't even have water etc, and I don't mind the idea of getting off the electric grid either, even with everything you've said. This country already has enough power outages that even the mains grid isn't that reliable anymore. I do agree though on spending a bit more to get better gear, and to add some extra redundancy in to the system too.
    • You can set hard reserves on your battery system, and it can't be discharged past that.  
    • That sounds like an excellent idea. But total self-sufficiency means exactly that. You have no-one else to blame when your system faults out and you have no power for a week or two while it gets fixed. You'd have to go the whole hog and get a diesel genny and all the switchover gear, to get you through such times. And, despite the fact that over 20 years, my system has been pretty reliable**, I have seen so many inverter explosions (or less dramatic deaths), panel and roof JB fires, and so on, over that time, to know that the stuff is the same as any other bulk Chinese manufactured stuff. The failure rate is well above zero - both on the equipment and on behalf of the meth addled installation labour force. And then..... warranty and means of redress against the supplier you bought the gear from. Best I can tell is that only a handful of solar companies are still around within 5 years of starting their advertising pitch. They disappear and phoenix like crazy. So, as per 1st paragraph, I suspect the only way to is go balls deep and spend maybe 2-3 times as much as you might think, so that you have every base covered. Plus, know and understand your gear intimately, so you can diagnose problems, sort them out yourself, etc, etc. Plus, probably have to consider upgrading various parts as the years pass, to maintain compatibility with newer stuff, performance and reliability, etc, etc. Whereas, remaining attached to the grid has an ongoing cost that keeps going up even if you use bugger all power from it. But it does provide the fallback in case of the worst case with your own gear. You either pay up front or as you go, I suspect.
    • Add more solar panels to the array. Call the electricity company and tell them you're moving out... Live off grid electric wise
×
×
  • Create New...