Jump to content
SAU Community

Recommended Posts

Hi there,

Looks like a good place for any questions on stagea's. Just signed up, from NZ.

After owning a few Toyota all wheel drives that ppl thought where Subaru leperosy's (my Toyota's broke down far less), I deiced to go back a step to a 1996 RWD stagea, something with more tit and less parts to fix. I think they're terrific to drive. Suspension is the most road comfortable I've ever driven in the past few years appart from the 350Z I had for a week on loan. Thought I'd never own a Nissan, as they seem to rust quicker than a lot of others I've had (that doesn't seem to have changed much), but they this is my first Nissan and their comfort level for bad backs is tops.

I dunno if mine was a good price to pay or not, but I got mine for $8,700NZ with 92KM's. Had the power steering pipework replaced under warranty and a new rear main engine seal and re-silicon job on the aluminium plate on the bell-housing from an anoying bloody slow oil leak (turned out to be a pin-hole in the plate joining but looked like a rear main). Dealer got everything done under warranty including the stuff that didn't need done, no excess. Now I fell like I have a decent car.

I plan on getting the owners manual in english from Aussie and a workshop manual for the RB25DE some time afterwards. Car sales guy said it runs on 91 octane? although I'm running it on 96, I read somewhere the compression ratio of the 2.5L is designed for premium. 96 octane is the highest where I live, 98 in the bigger cities, so I went with 96. These things must have a knock sensor cause on 91 it was fine for a few full tanks.

Does anyone know if there are child seat tether points in the stagea wagons? I've got a little hook right behind the middle rear seat belt behind the seat, but it's anchored with a wide bar through the seat stitching which I don't think it's a tether point as I would have imaged it's for bolting. The rear cargo one's don't seem to be in a good spot for this use either.

Cheers,

Gavin.

Link to comment
https://www.sau.com.au/forums/topic/54877-new-rwd-owner/
Share on other sites

Gavin,

Welcome to Stageas Australia.

It seems like all the NZ guys with stageas are flocking over here like sheep (oops sorry j/k poor taste). In all seriousness though congrats on the purchase I am sure you car will be very rewarding. Just to answer a few questions for you yes the cars are designed to run on premium unleaded fuel i think in japan they have 100 ron or higher butall we get in aus is 98 ron but if you get any knocking issues you can always add octane booster to each tank.

The child restraints are in the ceiling in the luggage compartment just inside the rear hatch. They should be covered by little black plastic dust covers. In the ones in Aus they add one in the centre position for compliance but in japan domestic models i am sure that they ony have 2 one for each outboard seat obviouldy due to less strict legislations. The little hook you mentioned is one of the cargo tie downs and i think its used to secure the optional (on series one models anyway) cargo net.

If you need any more info on specs and whatnot have a squizz at this may help a bit (btw sites still under construction) http://www.geocities.com/mcnamg/

Hope this helps

Cheers Glenn

Link to comment
https://www.sau.com.au/forums/topic/54877-new-rwd-owner/#findComment-1072258
Share on other sites

I dunno what's up with the sheep thing and aussies. We've got far less per capita here lol. I'm half aussie anyway & the missus is a 100% aussie.

RE: octane, seems to run on 91 regular ok, so I went to 96 premium and still seems as good as. I had a feeling it should be running at least 96, I didn't think a skyline type engine should be on anything less unlike the sales guy. It's $1.31 a litre for 96 here which I don't mind, dunno what 98 is worth. I could also pump some $4.31 a litre avgas 115 octane at the areoclub, that'd be fun.

Yip, I know the cargo net tie downs above the rear strut wells, I have my net up (it's a 25X model). Plus there's the 4 on the floor for another third party net or rope. But this one's behind those spring-hinged flaps that go up and down with the seat to cover the gap between the folding part of the middle seat and the bottom of the seat. It just doesn't seem secure enough to me compared to the cargo one's. Oh well, I flicked an email to Nissan NZ to see if they have other ideas.

I pulled off all the plastic clip covers in the rear just then to see, but they are only screw covers for the clips. I think they're for those pull-out covers which mines missing. I love the idea of the cigarette socket in the back, very handy.

BTW, what RPM does the 4 speed auto cruise at on 100KM's? Mine's 2400, usually 1900-2000 in 3rd around town. I don't feel the converter lock up in mine, haven't gotten that in tune with the drive line yet. Although I do notice it kicks a tad after acceleration then taking the foot of the gas. But I've noticed all auto's do this, this one is just a little more noticable having a 6 cly in it and a little more hevy.

Cheers,

Gavin.

Link to comment
https://www.sau.com.au/forums/topic/54877-new-rwd-owner/#findComment-1072300
Share on other sites

i think you may need to put the anchor points in yourselft for the child restraints but they are located in the roof to make sure cargo space isnt comprimised.

The cargo net has about 4 configs you can use it in maybe its meant to be used for another of those but i dont know which one sorr

Link to comment
https://www.sau.com.au/forums/topic/54877-new-rwd-owner/#findComment-1072321
Share on other sites

RE: octane, seems to run on 91 regular ok, so I went to 96 premium and still seems as good as. I had a feeling it should be running at least 96, I didn't think a skyline type engine should be on anything less unlike the sales guy.  It's $1.31 a litre for 96 here which I don't mind, dunno what 98 is worth. I could also pump some $4.31 a litre avgas 115 octane at the areoclub, that'd be fun.

The 2.5L NA Skylines engines have a quite high compression ratio (10.something:1), so 96 is definitely recommended. I run 98 in my GTS25 Skyline (same engine as your 25X), found that the $'s/km work out to be pretty much the same as 96 - costs 5 - 10% more but gets me 5 - 10% further per tank.

Link to comment
https://www.sau.com.au/forums/topic/54877-new-rwd-owner/#findComment-1073346
Share on other sites

hey hey welcome kiwi rock!!!!!!! -

new here myself, hope u enjoy the stag,

i'm still waiting for the wife to pick up mine-i mean ours- even then it will be end of november before i'm back in Auckland to drive it (in Christchurch at the moment) but it is essentially her car for work in the week :D

i'll put my mark on it though - soon enough :D

dont foget to visit here

http://forums.skylinesdownunder.co.nz/

some stagea owners/users from here on there too!

....ahh the family is growing....

Link to comment
https://www.sau.com.au/forums/topic/54877-new-rwd-owner/#findComment-1073352
Share on other sites

Hi & welcome to our (fast growing!) collection of Stagea owners. Get your owners manual from http://www.jpnz.co.nz

My RSFourV will lock up the converter at speeds as low as 55km/h (or thereabouts), but only in ideal cruising conditions. It's a far more intelligent shift pattern that a lot of cars I've driven. 100km/h rpms are around 2200 I think. However, the lockup is almost not noticable to the occupants, the only way to be certain is to gently squeeze the throttle open a few % and notice the lack of rpm flare.

Link to comment
https://www.sau.com.au/forums/topic/54877-new-rwd-owner/#findComment-1073570
Share on other sites

I found it, the torque converter locking up. With OD locked at about 90K's there's a sudden 300RPM reduction (hardly noticable as someone mentioned). Sits on 2350RPM at 100K's I've decided on the reasonbly flat road.

Got a reply from Nissan re: tether points, none for this import year from Japan. Oh well, 6 months to sort that out. Nissan NZ are faster at looking up stuff and replying to emails than a few other's I've delt with, considering it's a Jap import.

Spent today removing the rear hatch seal (after checking for any hidden anchor points) and doing some sanding/air painting at the bottom of the panel joints near the hatch door bolt. Found some light rust under the seal there, but nothing I couldn't sand back with the drill and repaint, then re-tighten the seals grasp. :idea: Which brings me to another question, why on earth does the rear hatch have an electric motor to help the locking mechanisim latch down on the door? Least it stops the missus from slaming it now.

:idea: Hey & how do I tell if I have a limited slip diff? Sometimes I get stuck, second attempts are fine up the likes of a 35 degree grassy slope. I found putting the hand brake on slightly was enough to stop wheel spin to get moving once. So I'm guessing it's proberly all open in the RWD?.

Thanks for all the replies guys, hugely appreciated. I'll go have a nosey on the .co.nz forums soon.

Cheers,

Gavin. :rofl:

Link to comment
https://www.sau.com.au/forums/topic/54877-new-rwd-owner/#findComment-1076308
Share on other sites

dude, close the boot lid very very slowly, like you might do by accident and leave it ajar slightly. Listen carefully and you will hear a click, watch in amazement as the boot pulls itself closed witha whirring sound and clicks into the locked position. No more slamming required. Let it fall in place lightly and it will lock itself closed everytime.

;)

Link to comment
https://www.sau.com.au/forums/topic/54877-new-rwd-owner/#findComment-1076577
Share on other sites

RE: octane, seems to run on 91 regular ok, so I went to 96 premium and still seems as good as. I had a feeling it should be running at least 96, I didn't think a skyline type engine should be on anything less unlike the sales guy. It's $1.31 a litre for 96 here which I don't mind, dunno what 98 is worth. I could also pump some $4.31 a litre avgas 115 octane at the areoclub, that'd be fun.

------------------------------------------------------------------------------------------------------

I ran my 25X Four for 1000km on Shell 91 and 1000km on 96, it works out 80cents per 100km cheaper to us 96, even though it is 5c per litre dearer - plus it responds better to the right foot on 96.

As for revs, mine sits at around 2500 on the rev counetr at 100kph, torque converter only locks up when it warms up, which can take 10km in the winter with my car. Before that it sits at 2700rpm, and you can feel it lock up, sort of like a really soft change.

BTW -- I've been told not to go into overdrive under 80kph, as the Torque converter bearing can stuff up and cause NZ$2700 overhaul!! Of course don't use OD when towing either - great tow cars these, although they drink the gas when towing a caravan!

Link to comment
https://www.sau.com.au/forums/topic/54877-new-rwd-owner/#findComment-1083054
Share on other sites

I've thought about doing some towing with it, although I'll have to ad a towbar first, then perhaps a transmission cooler. After reading about that weird idlign issue, mine seems to run fine, starts up at 1,500 til the airbag's do a check, then sits on 1,200 cold, then 700 warm. Brakes don't seem to make any difference.

Well after having the rear main seal replaced one week, new silicon seal done on the rear aloy gasket the next week, I think the bugger still hasn't stopped leaking a drip of oil every 400K's, or at least showing signs of a slight leak on the bottom of the bell housing (fingers crossed it's still residue from replacing the main rear).

Mechanics had it up on a hoist running for 2 hours after pressure testing the engine and re-sealing the bellhousing, then as always, get it home, plonk on the K's... then it shows up a slight trace of a new leak they keep missing, not dripping yet, but it's slowly gathering on the bottom of the bell housing, and doesn't appear to be run off from anywhere else but the seal or from the little vent hole used to lock the fly wheel up. Think I'm just having a bad run with pin holes in the gasket sealant at the rear, or fingers crossed before I get time to have the transmission pulled out again that it goes away.

Otherwise I'm still impressed with it's condition otherwise, already used to have a 6 cylinder.

Cheers,

Gavin.

Link to comment
https://www.sau.com.au/forums/topic/54877-new-rwd-owner/#findComment-1083538
Share on other sites

  • 2 weeks later...

The mechanics filled the engine oil to just over the "H" on the dipstick but below the indent on the stick its self. After getting the rear main and the gasket's done, I've emptied about 500ml to get the oil level spot on the top of the cross-hatch below the "H' letter. Where abouts do you guys fill it to?

Cheers,

Gavin.

Link to comment
https://www.sau.com.au/forums/topic/54877-new-rwd-owner/#findComment-1097168
Share on other sites

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now


  • Similar Content

  • Latest Posts

    • Thought I would get some advice from others on this situation.    Relevant info: R33 GTS25t Link G4x ECU Walbro 255LPH w/ OEM FP Relay (No relay mod) Scenario: I accidentally messed up my old AVS S5 (rev.1) at the start of the year and the cars been immobilised. Also the siren BBU has completely failed; so I decided to upgrade it.  I got a newer AVS S5 (rev.2?) installed on Friday. The guy removed the old one and its immobilisers. Tried to start it; the car cranks but doesnt start.  The new one was installed and all the alarm functions seem to be working as they should; still wouldn't start Went to bed; got up on Friday morning and decided to have a look into the no start problem. Found the car completely dead.  Charged the battery; plugged it back in and found the brake lights were stuck on.  Unplugging the brake pedal switch the lights turn off. Plug it back in and theyre stuck on again. I tested the switch (continuity test and resistance); all looks good (0-1kohm).  On talking to AVS; found its because of the rubber stopper on the brake pedal; sure enough the middle of it is missing so have ordered a new one. One of those wear items; which was confusing what was going on However when I try unplugging the STOP Light fuses (under the dash and under the hood) the brake light still stays on. Should those fuses not cut the brake light circuit?  I then checked the ECU; FP Speed Error.  Testing the pump again; I can hear the relay clicking every time I switch it to ON. I unplugged the pump and put the multimeter across the plug. No continuity; im seeing 0.6V (ECU signal?) and when it switches the relay I think its like 20mA or 200mA). Not seeing 12.4V / 7-9A. As far as I know; the Fuel Pump was wired through one of the immobiliser relays on the old alarm.  He pulled some thick gauged harness out with the old alarm wiring; which looks to me like it was to bridge connections into the immobilisers? Before it got immobilised it was running just fine.  Im at a loss to why the FP is getting no voltage; I thought maybe the FP was faulty (even though I havent even done 50km on the new pump) but no voltage at the harness plug.  Questions: Could it be he didnt reconnect the fuel pump when testing it after the old alarm removal (before installing the new alarm)?  Is this a case of bridging to the brake lights instead of the fuel pump circuit? It's a bit beyond me as I dont do a lot with electrical; so have tried my best to diagnose what I think seems to make sense.  Seeking advice if theres for sure an issue with the alarm install to get him back here; or if I do infact, need an auto electrician to diagnose it. 
    • Then, shorten them by 1cm, drop the car back down and have a visual look (or even better, use a spirit level across the wheel to see if you have less camber than before. You still want something like 1.5 for road use. Alternatively, if you have adjustable rear ride height (I assume you do if you have extreme camber wear), raise the suspension back to standard height until you can get it all aligned properly. Finally, keep in mind that wear on the inside of the tyre can be for incorrect toe, not just camber
    • I know I have to get a wheel alignment but until then I just need to bring the rear tyres in a bit they're wearing to the belt on the inside and brand new on the outside edge. I did shorten the arms a bit but got it wrong now after a few klms the Slip and VDC lights come on. I'd just like to get it to a point where I can drive for another week or two before getting an alignment. I've had to pay a lot of other stuff recently so doing it myself is my only option 
    • You just need a wheel alignment after, so just set them to the same as current and drive to the shop. As there are 2 upper links it may also be worth adding adjustable upper front links at the same time; these reduce bump steer when you move the camber (note that setting those correctly takes a lot longer as you have to recheck the camber at each length of the toe arm, through a range of movement, so you could just ignore that unless the handling becomes unpredictable)
    • I got adjustable after market rear camber arm to replace the stock one's because got sick of having to buy new rear tyres every few months. Can anyone please let me know what the best adjustment length would be. I don't have the old ones anymore to get measurements. I'm guessing the stock measurement minus a few mm would do it. Please any help on replacing them would be fantastic I've watched the YouTube clips but no-one talks about how long to set the camber arm to.
×
×
  • Create New...