Jump to content
SAU Community

Recommended Posts

Jaqule200411021811readfile2.jpg 1995 S1 GTST 33

Custom Paint : Ford blue print blue with candy apple pearl and super fine flake, also dash and door trim in same color

Aero kit : 400R front bar/rear bar , Nizmo side skirts , Stealth/drift wing , yellow ribbon decal

Suspention&wheels : Tien Adjustible HA , Sparco racing 17x9" 235/45 front , sparco 17x10" 255/40 rear sprayed Metalic Black, frount strut brace.

Intake&Zaust : Apexi power intake pod , Cold air Box with cold air pipe to frount bar, 3" Zaust from dump pipe back, 600x300x76 Frount mount, GFB hybrid BOV

Engine mods&mis : Profec B spec II Elec Boost Ctl , Apexi TT, boost gadge/Oil temp on A piller, and soon to have a Apexi SAFC , White face GTR dash.

Stereo : Clarion (Dx546 I think ) MP3, WMA , Clarion 6" splits and 2 ways

comes with full tank and a free hug $ 25k

Link to comment
https://www.sau.com.au/forums/topic/54925-selling-the-line/#findComment-1072966
Share on other sites

Thanks guys :grouphug: , I will get some done on the dyno day and if I need more I will come and see either Melv or Gordo and get a few proper one's with a nicer background :bananaman

thanks again :P

Link to comment
https://www.sau.com.au/forums/topic/54925-selling-the-line/#findComment-1073671
Share on other sites

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now


  • Similar Content

  • Latest Posts

    • There's restrictor pills in the stock boost control hoses. That's how they set the amount that was bled off and hence the "high" boost setting. The usual mod in the day was to remove it and send the "high" boost setting up to about 14 psi.
    • Thanks Duncan, that's the best info I've read. Furthermore after learning about the PCM programming side controlling the factory boost solenoid, the purpose of the solenoid is to "bleed" boost when pin 25 is earthed, thus allowing spring pressure in the wastegate actuator to overcome diaphragm boost pressure, thus closing or reducing the position of the wastegate flap creating more boost as the turbo is able to spin faster. It's pretty cool to see a designated Pill to do exactly this, would have liked to have seen it with a tiny filter over the end for those moments in vacuum.  The constant bleed pill has now been removed completely from the system and solenoid boost control has been restored once again.   Case closed 😂
    • The wideband reading is meaningless if it's not running. Why are you using shitty old sidefeeds on any engine, let alone a Neo? What manifold and fuel rail are you using to achieve that? Beyond that, can't help you with AEM stuff as I've never been their ECU/CAS combo.
    • Manual boost controllers (where a little of the boost was bled off) were quite common back in the day, because they were cheap and easy. Generally they had a manual adjustment screw rather than being fixed like yours. Down side is they always bleed boost, not just when you want them to so an electronic boost controller that uses a solenoid will have less lag.
    • Hello , im new here and i have A31 home build  RB25det neo stock eng / turbo  aem ems 2 blue connector  aem 3.5 map aem cas disk aem wideband connected to ecu  355 lph pump 550 nismo yellow injectors side feed aftermarket regulator  and won’t start with base aem tuner basic tune eventually flipped cas 180 degree so it triggers on correct stroke not in exhaust cycle  Now it won’t start Wideband reads 10 and 11 at lowest fuel setting  and will share calibrations soon for aem tuner i think something is wrong in aem tuner    please if you have any information, am very grateful         
×
×
  • Create New...