Jump to content
SAU Community

Recommended Posts

Nice!

Got similiar parts installed on my car already except turbo is a Garrett GT35 and boost controller is HKS EVC 3.

Do the internals first before it blows and save youself alot of labour costs from getting everything installed and then removed to get the internals done later.

Have YOU done your internals?

  • Replies 91
  • Created
  • Last Reply

Top Posters In This Topic

and youve got a GT35 inasnt?

:D dont make me laugh. You aint got a GT35 and you know it.

b33st - you can use RB26 rods, $400 and prepping.

I've got em in mine, and a lot of people do it as 26 rods are pretty decent for the buying price

and youve got a GT35 inasnt?

:)   dont make me laugh. You aint got a GT35 and you know it.

b33st - you can use RB26 rods, $400 and prepping.

I've got em in mine, and a lot of people do it as 26 rods are pretty decent for the buying price

GT30 Actually, i was flying over perth when i typed that :)

  • 2 weeks later...

Ok i've decided to be a little more patient and wait till i got the cash and do internals properly at the same time. Looking at forged rods (crower), Pistons (venolia) looking for people opinions on this. Also What rings, bearings, headgaskets (brands, thinknesses) are people using. Crank i am just looking at balancing and probably nitrating.

Plan is to buy parts then get someone to bolt the engine together for me.

  • 3 months later...

OK i've held off a little but and gone the whole hog. Going to it properly and all at once, internals and all. Have perchased venolia 20 thou over pistons and am now about to purchase a set of rods.

i have priced up the following.

Crower $2100

Argo $2300

Par $1800

I personally am leaning towards the par one's as the price is good. Any one used these or have an opinion on them.?

  • 1 month later...

Starting to get somewhere now. After 2 years of buying bits and pieces work has actually started on the car. Just finished lifting the engine out now. Was going the spend the day stripping it down but had no bolts long enough to attach it to the engine stand.

Got her on the stand and stripped down today. Bores look perfect!

I am away on holidays next week for a few weeks then it's time to get some machine work done. Will probably get the head sorted first, just a mild port new and some stiffer springs. Not too sure if i will do the valves too.

  • 2 months later...

Engine is at the Machine shop now.

Head is getting ported, tomei springs and cams

block getting bored, honed and o-ringed.

Everything is to be balanced (standard crank, Argo Rods, Venolia pistons),

using ARP Head stud kit and standard thickness copper head gasket and ACL Bearings.

  • 4 months later...

Time for another update.

My Engine is now completed and will be picking it up from the engine builder some time this week if i can find the time.

I ended up shelving my Venolia pistons as didn't want to run the clearances that they specified and also wanted to drop the comp at little, CP pistons have gone in in their place.

Also didnt go with the copper gasket just a cometic MLS.

Heads ported, new tomei cams and springs, new guides also but reused the standard valves.

I can't belive this is taking so long but at least it is progressing. I just hope i'm back on the road by christmas.

Edited by B33st

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now



  • Latest Posts

    • If the forester is anything like our old 2007 GTB Liberty, I could near on run ling Long's and "rate them", as no matter what, it just hung to the road, even when abusing it in a hard launch in the wet, or throwing it at corners.
    • LOL, all of the CAI like Craig I just need to put a hole saw through my bumper Done and dusted, the car runs, which is nice, I'll take it for a spin when the weather clears up Just need to put the bumper back on for good
    • Brooooo Please send ABS control unit schematic Please! R33 gts25t ABS (Its two plug ecu, black and white) wire colors possible? [email protected]
    • Don't even try to run it on the stock ECU if you're going to have the boost controller bring boost above ~10 psi. I've already told you that. If you use the Nistune ECU, you will need to CAREFULLY read the available documentation for Neo tuning, and read some threads on the Nistune forums, to discover the various things you have to do to prevent the ECU from going bananas when the boost is too high. The is a table associated with th boost sensor that must be modified to prevent it from shitting the bed. This is just one of the things that you will need to do to the tune in Nistune, because the Neo turbo ECU will be expecting to see a number of things (such as the TCS) that are not there, and you have to block the DTCs on those. It is totally not surprising to me that you are having the problems that you are, but the solutions to these problems have been known for >15 years. So just get it done.
×
×
  • Create New...