Jump to content
SAU Community

Recommended Posts

i just dont understand why people spend $500-800 on a good exhaust and dont even blink but then can't part with th money when it comes to something like coils or injectors???

So what if it does the power on stock injectors, why would you want to, ther are cheap in relevance to everything else you have modified to get to that power level??? Let me get this right,

turbo and associated piping- $2000

ECU and Install- $2500

Intercooler, exhaust, cams, cam gears and other assciated good- $2000

Expecting your engine to last at high power levels with piss poor 370cc injectors,

PRICELESS.

There are some things money can't buy, but injectors shouldnt be one of them...

built motor $7K

turbo + Bits $5K

cooler $2K

ecu $2k

Diff $1k

clutch $1.2K

Fuel System $1.3k

the one thing i dont need .... bigger injectors i dont need them.

some things in life you should not coment on, for others think before you type.

  • Replies 237
  • Created
  • Last Reply

Top Posters In This Topic

Fuel pressure is 30psi and rises to 50psi under full boost.

And how much psi boost do you need to run to make that power? The 511rwhp is BS as sst-steve said in the other thread right? So you have you still got it in your signature and as the title of this thread?

1.3K fuel system witout changing injectors? What was the 1.3K spend on then?

the advantage of running smaller injectors is that the spray pattern is better

On a sequential fire, I see your point but, what is the importance of spray pattern if your ECU is using batch fire...?

The fuel pools behind the intake valve till it opens.

Pooling may be the wrong word but, it still doesnt inject the fuel at the right time that corresponds with the opening of the intake valve. Why is majority of the industry adopting sequential fire if it didn't make a difference...?

So, again, what is the importance of spray pattern in batch fire...?

the advantage of running smaller injectors is that the spray pattern is better

That's simply not true, take a look at the 1,000 cc Bosch Motorsport injectors. The 370 cc RB25DET injectors are crap compared to them. Plus the spray patterns are selectable for close, mid and long inlet. I have absolutely no doubt you would get better everything using them, max power, average power, idle quality, emmisions and fuel economy would all benefit.

The reality is there is nothing that the standard injectors do better than many aftermarket injectors. As long as the ECU can control them of course.:D

As we have good economy and drivability and good emissions and reliability and no tuning problems even with 1000cc injectors and set the pace in WA Wheres the problem?

This is all getting weak and making you guys look like clowns. Wolf is not the worlds best ECU but it does a bloody good job and is well priced and garranted and very flexible and im happy to sell and support it.

ROFL...

We don't have a problem with Wolf, infact we'd like to know more about it.

The problem lies with you and your attitude that everyone is against you from the start. Example : Sydneykid didn't suggest Tristian should buy 1000cc injectors, he just corrected him and used 1000cc injectors as a reference.

Why start controversial threads, ignore the questions in it, than have a sook half way through it and ask it to be closed.

Why have the need to show yourself as ahead of every other tuner in the country...?

Who exactly is the clown...?

I am not from WA and neither are the big majority of the forum users.

So, I'm sorry your humour had gone straight passed me.

BUT, if that was the case, why didn't you put your thread in WA section...?

More importantly, why did you address it to all the people in eastern states...?

:)

The origional post is still a fact ,Tristan made 511rwhp on stock injectors on Speedworks dyno and if you were from WA you would know why thats funny.

I have avoided a direct face off up to now, but this one is TOOOOO much.

It was a HUB DYNO

The car did'nt have the rear wheels on it

They took them off to mount the dyno cells to the hubs

If it had no rear wheels on it, it can't make RWHP

R= Rear

W= Wheel

HP= Horsewpower

The post is WRONG, it should read RHHP

R= Rear

H= Hub

HP= Horsewpower

Other than that I have no problems:cheers:

PS, well I suspect that Tristan himself didn't make 511rhhp, it was actually Tristan's car.

my prices where rough sorry but my point still stands and i agree with SK and suggested it in my original thread, you have everything to benefit from bigger injectors so why is it so great to do big power on stockies that turn your engine into a timebomb??? Its like building a mansion then saying dont worry about using steel reinforcement ive seen people use timber on 2 bedroom houses that will do, back to the car If you have spent so much effort, time and money insuring reliabilty and performance everywhere else why skimp on the foundations, i dont dispute that you think the wolf is great, or the fact ot does the power i just cant fathom the mentality of doing it this way! Oh and my thought-out post was accepted everywhere common sense is, over 1000 locations Australia wide. (just keeping the mastercard thing going for you).

Guest
This topic is now closed to further replies.



  • Similar Content

  • Latest Posts

    • From there, it is really just test and assemble. Plug the adapter cables from the unit into the back of the screen, then the other side to the car harness. Don't forget all the other plugs too! Run the cables behind the unit and screw it back into place (4 screws) and you should now have 3 cables to run from the top screen to the android unit. I ran them along the DS of the other AV units in the gap between their backets and the console, and used some corrugated tubing on the sharp edges of the bracket so the wires were safe. Plug the centre console and lower screen in temporarily and turn the car to ACC, the AV should fire up as normal. Hold the back button for 3 sec and Android should appear on the top screen. You need to set the input to Aux for audio (more on that later). I put the unit under the AC duct in the centre console, with the wifi antenna on top of the AC duct near the shifter, the bluetooth antenna on the AC duct under the centre console The GPS unit on top of the DS to AC duct; they all seem to work OK there are are out of the way. Neat cable routing is a pain. For the drive recorder I mounted it near the rear view mirror and run the cable in the headlining, across the a pillar and then down the inside of the a pillar seal to the DS lower dash. From there it goes across and to one USB input for the unit. The second USB input is attached to the ECUtec OBD dongle and the 3rd goes to the USB bulkhead connected I added in the centre console. This is how the centre console looks "tidied" up Note I didn't install the provided speaker, didn't use the 2.5mm IPod in line or the piggyback loom for the Ipod or change any DIP switches; they seem to only be required if you need to use the Ipod input rather than the AUX input. That's it, install done, I'll follow up with a separate post on how the unit works, but in summary it retains all factory functions and inputs (so I still use my phone to the car for calls), reverse still works like factory etc.
    • Place the new daughterboard in the case and mount it using the 3 small black rivets provided, and reconnect the 3 factory ribbon cables to the new board Then, use the 3 piggyback cables from the daughterboard into the factory board on top (there are stand offs in the case to keep them apart. and remember to reconnect the antenna and rear cover fan wires. 1 screw to hold the motherboard in place. Before closing the case, make a hole in the sticker covering a hole in the case and run the cable for the android unit into the plug there. The video forgot this step, so did I, so will you probably. Then redo the 4 screws on back, 2 each top and bottom, 3 each side and put the 2 brackets back on.....all ready to go and not that tricky really.      
    • Onto the android unit. You need to remove the top screen because there is a daughterboard to put inside the case. Each side vent pops out from clips; start at the bottom and carefully remove upwards (use a trim remover tool to avoid breaking anything). Then the lower screen and controls come out, 4 screws, a couple of clips (including 3 flimsy ones at the top) and 3 plugs on the rear. Then the upper screen, 4 screws and a bunch of plugs and she is out. From there, remove the mounting brackets (2 screws each), 4 screws on the rear, 2 screws top and bottom and 3 screws holding in the small plates on each side. When you remove the back cover (tight fit), watch out for the power cable for the fan, I removed it so I could put the back aside. The mainboard is held in by 1 screw in the middle, 1 aerial at the top and 3 ribbon cables. If you've ever done any laptop stuff the ribbon cables are OK to work with, just pop up the retainer and they slide out. If you are not familiar just grab a 12 year old from an iphone factory, they will know how it works The case should now look like this:
    • Switching the console was tricky. First there were 6 screws to remove, and also the little adapter loom and its screws had to come out. Also don't forget to remove the 2 screws holding the central locking receiver. Then there are 4 clips on either side....these were very tight in this case and needed careful persuading with a long flat screw driver....some force required but not enough to break them...this was probably the fiddliest part of the whole job. In my case I needed both the wiring loom and the central locking receiver module to swap across to the new one. That was it for the console, so "assembly is the reverse of disassembly"
    • But first....while I was there, I also swapped across the centre console box for the other style where the AV inputs don't intrude into the (very limited !) space.  Part# was 96926-4GA0A, 284H3-4GA0B, 284H3-4GA0A. (I've already swapped the top 12v socket for a USB bulkhead in this pic, it fit the hole without modification:) Comparison of the 2: Basically to do the console you need to remove the DS and PS side console trim (they slide up and back, held in by clips only) Then remove the back half of the console top trim with the cupholders, pops up, all clips again but be careful at the front as it is pretty flimsy. Then slide the shifter boot down, remove the spring clip, loose it forever somewhere in the car the pull the shift knob off. Remove the tiny plastic piece on DS near "P" and use something thin and long (most screwdrivers won't fit) to push down the interlock and put the shifter down in D for space. There is one screw at the front, then the shifter surround and ashtray lift up. There are 3 or 4 plugs underneath and it is off. Next is the rear cover of the centre console; you need to open the console lid, pop off the trim covering the lid hinge and undo the 2rd screw from the driver's side (the rest all need to come out later so you can do them all now and remove the lid) Then the rear cover unclips (6 clips), start at the top with a trim tool pulling backwards. Once it is off there are 2 screws facing rearwards to remove (need a short phillips for these) and you are done with the rear of the console. There are 4 plugs at the A/V box to unclip Then there are 2 screws at the front of the console, and 2 clips (pull up and back) and the console will come out.
×
×
  • Create New...