Jump to content
SAU Community

Recommended Posts

I found a supplier who can supply this for $35 each + postage from HK, which seems pretty cheap.

i am looking at 2 for myself and see if anyone is interest too.

1 carton is 12 sets.

size is 1:24

available:

R34 GTR (grey, blue)

350Z nismo Z-tune

350Z option's car (orange)

Apexi D1 Rx7

Mazda speed Rx7

metal made panel (not cheap cheap plastic)

come with all sort of mod (as seen in Pic)

height adjustable suspension

adjustable camber, offset

Link to comment
https://www.sau.com.au/forums/topic/55442-eoi-gb-of-this-diecast/
Share on other sites

  • 4 weeks later...

alright, so are u 2 confirm u want it?

as they are so cheap i am not going to bother collect $ b4 hand

i will make the order once u 2 confirm

the postage i estimate will be around $30-$40 for all 3 by air (will show the postage)

so total MUST under $50

i spot NS.com someone asking $85 for it, that's not include delivery :rant:

Andrew - 1 x GTR

Darren - 1 X grey GTR

sskylinee - 2 x GTR (grey & blue)

VIPERGTSR01- 1x blue GTR

Me x 2

PIE ?

Nozila ?

12 per carton, 3 more to go

if we can do it b4 end of next week, should arrive as a christmas present :(

updated the first post for a bit more information too

as the number of suddenly increase, it's a bit hard for me to estimate the postage.

I will confirm the postage soon, if it is very expensive, i might try sea instead of air.

Andrew - 1 x GTR

Darren - 1 X grey GTR

sskylinee - 2 x GTR (grey & blue)

VIPERGTSR01 - 1 x blue GTR, 1 x nismo 350z

mr34 - 1 x grey GTR

Me x 2

PIE ?

Nozila ?

11 now if PIE and Nozila order

i might just get the last one and sell it for $85 somewhere else... :)

done.

the GB is finish

Rezz in Japan pay a$53 for his and asking 112 to land in Aus :D

http://www.skylinesaustralia.com/forums/sh...56&page=1&pp=25

Andrew - 1 x GTR

Darren - 1 X grey GTR

sskylinee - 2 x GTR (grey & blue)

VIPERGTSR01 - 1 x blue GTR, 1 x nismo 350z

mr34 - 1 x grey GTR

Me x 2

Nozila - 1 x grey GTR

Mad GT4 - 1 x grey GTR

grepin - 1 x grey GTR

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now


  • Similar Content

  • Latest Posts

    • Have you done the Ignition Sync Wizard in the AEM software?
    • Find out what RPM it was idling at with the IACV unplugged. It's very weird that the rpm didn't change at all, and then it stalled. When it stalls is it nearly like a switch off, like you've turned the engine off? Or is it more stutters and sputters and coughs to death over a few seconds? Or does the RPM just slowly keep going down and down? Have you done a test of trying to start it with the AFM unplugged? Does it still die?     If you Follow Josh's advice on using Nistune to check the voltages (which is a perfect method!) if you see anything out of wack voltage wise, THEN get the multimeter out and read the voltage directly at the sensor. If the two vary, then you're now looking for a wiring issue vs a sensor issue. So be aware, what the ECU sees, may not be what the sensor is actually saying too...
    • You very likely need to get it on a dyno and tune it. My assumption is, you've got an RB25DET tune in it, which has a different manifold, different injectors, and different cams as a minimum. What O2 sensor are you running?   When you say it runs extremely rich from idle all the way to redline, is this just free revving it you see that?
    • I seem to the be only person that is using a Haltech 2500 on an NA motor, I've installed a Bosch DBW throttle body to the OEM intake manifold and am having problems maintaining AFR even with the wideband o2.  It will run extremely rich at idle and up to redline, but under load it will go extremely lean in the 20s and i'm essentially having to rev it over 4k and feather the clutch to get it up to speed.  I've read a few other threads of about the butterfly, it seems removing the vacuum to it is supposed to have it remain open, i've noticed no difference under 4k with the vacuum line to it plugged.  I'm hoping someone here has had luck using the NA manifold with Haltech, and if they happen to have a tune for it.  
    • I don't know any details, but I really wouldn't be surprised if they do it as a LHD only version, at least initially.
×
×
  • Create New...