Jump to content
SAU Community

Recommended Posts

After putting the new turbos into the car, the oil dipstick is blowing out of the hole.

Before I put the new turbos in, I made sure the compression was OK and even in the engine (168psi when 171psi is the upper limit). Standard turbos, rebuilt to steel wheel and ball bearing specs.

I'm wondering whether the Exhaust Gas Recirculation system might be blocked - a look through Nissan Fast has me confused about where the valves are and what might be happening. The AAC valves also sem to have soemthing to do with this - buggered if I can figure it out.

Tuner reports the car is currently making about 170rwkw on 9psi boost, so I'd like to check that the crankcase ventlation system is OK before worrying about possible broken or rolled piston rings.

Could someone please give me an idea on how to check this part of the system, and what parts might be gunked up or blocked??

Cheers,

John

Pressure build up in the sump is proberly from worn piston rings, and on compression stroke air goes straight past them into sump and has to go out some were.... out the dipstick.

Are you loosing any oil ? blowing smoke from exhaust ?

If that's the case its rebuild time.

:P

Jun

Compression is 168. Can't see how it can be this high with badly worn or cracked rings.

Not using oil or smoke.

When turbos were stuffed there was a lot of gunk generated so I suspect a blocked PCV or some other part/tube around it that would normally take air from the sump and inject it into the inlets.

Where is the PCV and any other bits that could be the culprit? Is the PCV cleanable or replaceable? I can't find it in FAST or the manual. Personally I'm confused about the PCV vs AAC valve arrangement

Sounds like excessive blowby pressurising the sump. A dry comp test will not always show ringland damage in its initial stages, I'm with fats, but rather than retaining the dipstick with a spring run both breathers to atmosphere to relieve all pressure, start saving some $ and pull her when she really starts breathing.

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now


  • Similar Content

  • Latest Posts

    • Seat of the pants assessment of the new intake: The car is way less "doughy" when hitting the loud pedal, especially off idle when stopped or in traffic, I did use a cheapo lazer thermal thingo to measure the temp around where the pod filter got its air, it was between 55 - 60°C, in saying this the car was shut off and not moving, so the OEM intake pipe was not supplying any fresh air to where the pod was when the car was at least moving A weird bonus was induction noise on the throttle in the cabin increased a bit,  I was worried that I was actually going to lose some of that induction noise I love so much, outside though, when I got the daughter to do a WOT drive by pass for me, the induction noise has increased alot when on the throttle, not quite ITB doort, but well up there I'm extremely happy with the results and have been exploring the country roads in the region  As for house mods: 1.New front fence is up and is awesome, it really upgraded how the joint looks from the street, and the added security is nice 2. Electricians have replace some interior lights, and with more lighting in the garage, a few new motion detecting lights out the front above the garage, front room, and at the front door, which I have already found heaps helpful coming and going, also now has fancy pants CCTV all round the house The only hold point for power though is the solar and batteries due to supply issues, although this will happen over the next few weeks 3. I have done a heap of landscaping out the front and I'm almost ready to do a new small retaining wall with some nice blocks to replace the brick and cemented in rocks around the raised garden beds cemented in river stone "was the fashion at the time" the house was built. I currently have a pallet of retaining wall blocks and 2 bulka bags of 20mm blue metal to replace the wood chip that is in the raised garden beds around the house 4. I now have 3 big raised garden beds for out the back to grow some vegetables, about 70cm high, 200cm long and 100cm wide 5. My 2 compost bins are already pretty full with brown, green and kitchen waste from the landscaping I'vedone so far, but they will probably take a few months to break down, so anything else that gets chopped, trimmed, and kitchen waste will just start filling the base of the raised garden beds to about 30cm before I start throwing 40cm of good compost, and stuff, for the vegetables to grow in, I'll need a few ton of compost and soil, but the local supplier can sent me bulka bags of the stuff Basically the logs, wood chips and a few strategically placed rocks for drainage, will give the beds some good organic materials down low to break down over time, and they will hold moisture during the warmer months to save the water in my big arse water tank if we don't get alot of rain So, all in all, the car and house mods are going well, and I'm really enjoying being retired, I sleep in too 0700 and slowly plod around inside until I feel like actually doing anything, and only work in the yard for as long as want, which has actually been alot over the last few weeks,  although when you look at it, it seems that not a huge amount of work has been done,  until I look at the before I started the work pics Happy days and good times indeed 
    • hahaha yeah. Plan is to get side skirts and probably just rear pods. But going to do them one-by-one. I've got a set that I really like from RHDJapen, but that one isn't shipped to AU. So need to find someone who can get it for me
    • Here's an idea, answer the questions I asked you as they are trying to work out WHY the LSD will be binding up in a straight line.
    • You haven't driven many modern cars then have you? Most of them have sfa steering feel with their stupid electric bullshit steering systems.
×
×
  • Create New...