Jump to content
SAU Community

Recommended Posts

One of my exhaust wheels parted company the other day on my R32 GT-R so it's upgrade time. I have a Power FC and a Blitz SBCiD III already (not installed) and was thinking of adding turbo's, injectors, fuel pump and FMIC.

I've been thinking of a HKS 2530 kit but some posts have mentioned GT RS and GT SS. My priority is not really top end, quick spool up and midrange is what I think I'm after.

Secondly, what size/type of injectors should I be looking at?

Thanks in advance

Link to comment
https://www.sau.com.au/forums/topic/55536-which-turbos-do-i-want/
Share on other sites

sounds similar to my project (althoguh my stock turbos are still good :P ) I suggest the GT-SS kit, with 550cc - 700cc injectors and a nismo intank replacement pump.

Tuning, as always will be important - I'm not going to guess what your RWKW will be, as things vary but expect 300+ (mine makes 230 on the stockers with 10psi - stock ECU, inj, pump. 3in exh)

I'm going to be fitting GT2530's to mine (when I get the gaskets.....)

Good luck

I would suggest HKS GT2530/GT2540 or GReddy T517Z/T518Z. Dont rule out the N1 turbos (R34 is ball bearing i believe). Thats what i am running. There are a few turbos being sold on the forum and quite a few in ebay (search for GTR).

If your after response go for the GT-RS or SS the T517z's are a little laggy but the T517z and the GT-SS can make up to 300kw's+ (with a good tune)

I'd personaly go GT-SS or GT-RS as the response is really good on them, for the power they can produce. But the price is also expensive!

:P

Jun

GT-RS i thought were a bit laggy?

The GT-SS seem to be a good turbo for spool up to make over 300rwkw, or if you want to save a few dollars go for 2530, they will make more power, and be a tiny bit laggier than GT-SS

avoid the 2540's, GT-RS & T517z (10's), as these will all be too laggy on your application. That is why i went with the GT2530's. pick either GT-SS or GT530's..... (the GT-SS is the newer design). Someone on the forums made 290awkw on 18psi with the GT-SS, and is aiming for 350awkw....

I went for R32 N1s (group A) same size as the 2530s I believe. I got mine from the Jap yahoo actions through Slidewize imports, $1670 for both almost like new! A little laggier than the standard tubs but strong mid to top end.

R34 N1s would spool faster but probly cost an extra thou. Just depends on cost, I couldnt justify the cost of GT-SS tubs but they would be a good choice for the street.

I'd like the car to remain reasonably civilised, as I'd be driving it mainly on the street with the (very) occasional track day. I'm not a drag racer. As far as money goes...I'd prefer to pay a bit more if I thought I was getting what I wanted, but that doesn't mean I have unlimited funds!

I guess what I'm asking is, what is the on-road difference is between 2530's, GT SS's etc..

Thanks again guys, appreciate the advice.

I like 2530's, I prefer their average power. The GTSS's have more lower in the rpm range but not much, they loose more in the top end. I never use plain bearing turbos so the Trust's would not be on my list. I think 2540 's are the worst turbo pairing HKS have ever sold, they have a big mismatch between turbine and compressor sizing.

Bottom line, the GTR with the 2530 's made more power EVERYWHERE than standard and that's was enough for me.:P

I have r33 n1 's in mine and they are great . 2530 's or gtss 's i would go for .

the gtrs's are very laggy and you would need to run high boost 1.5 bar + .

I run 1.2 bar on my n1's and they pull hard from 4000 all the way to 8000 rpm.

I would check the engine if i was you before i install the new turbos . If you had the stock turbos with ceramic wheels and one let go you may find that the ceramic dust has gone through the engine and scored the bores . Which turbo let go ? the rear ? If yes check compression and do a leakdown test on the rear 3 cils to make sure you don't install good turbos then you have to pull the donk out .

One of my exhaust wheels parted company the other day on my R32 GT-R so it's upgrade time. I have a Power FC and a Blitz SBCiD III already (not installed) and was thinking of adding turbo's, injectors, fuel pump and FMIC.

I've been thinking of a HKS 2530 kit but some posts have mentioned GT RS and GT SS. My priority is not really top end, quick spool up and midrange is what I think I'm after.

Secondly, what size/type of injectors should I be looking at?

Thanks in advance

Guest two.06l
Bottom line, the GTR with the 2530 's made more power EVERYWHERE than standard and that's was enough for me.:D

You got that right S.K. We have the full HKS 2530 kit on Staceys car and for a street car, the response is second to none. With the correct cam selection and timing you cant go past them. Its even more surprising that the technology used to produce these is now nearly 15years old.Paul...DIRTgarage.

I like 2530's, I prefer their average power.  The GTSS's have more lower in the rpm range but not much, they loose more in the top end.  I never use plain bearing turbos so the Trust's would not be on my list.  I think 2540 's are the worst turbo pairing HKS have ever sold, they have a big mismatch between turbine and compressor sizing.

Bottom line, the GTR with the 2530 's made more power EVERYWHERE than standard and that's was enough for me.:D

SK as usual is on the money, the SS's are 1mm smaller in the compressor wheel so hit earlier, but for greater average power you can't go past 2530's.

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now


  • Similar Content

  • Latest Posts

    • Hi, is the HKS  Tower Bar still available ? negotiable ? 🤔
    • From there, it is really just test and assemble. Plug the adapter cables from the unit into the back of the screen, then the other side to the car harness. Don't forget all the other plugs too! Run the cables behind the unit and screw it back into place (4 screws) and you should now have 3 cables to run from the top screen to the android unit. I ran them along the DS of the other AV units in the gap between their backets and the console, and used some corrugated tubing on the sharp edges of the bracket so the wires were safe. Plug the centre console and lower screen in temporarily and turn the car to ACC, the AV should fire up as normal. Hold the back button for 3 sec and Android should appear on the top screen. You need to set the input to Aux for audio (more on that later). I put the unit under the AC duct in the centre console, with the wifi antenna on top of the AC duct near the shifter, the bluetooth antenna on the AC duct under the centre console The GPS unit on top of the DS to AC duct; they all seem to work OK there are are out of the way. Neat cable routing is a pain. For the drive recorder I mounted it near the rear view mirror and run the cable in the headlining, across the a pillar and then down the inside of the a pillar seal to the DS lower dash. From there it goes across and to one USB input for the unit. The second USB input is attached to the ECUtec OBD dongle and the 3rd goes to the USB bulkhead connected I added in the centre console. This is how the centre console looks "tidied" up Note I didn't install the provided speaker, didn't use the 2.5mm IPod in line or the piggyback loom for the Ipod or change any DIP switches; they seem to only be required if you need to use the Ipod input rather than the AUX input. That's it, install done, I'll follow up with a separate post on how the unit works, but in summary it retains all factory functions and inputs (so I still use my phone to the car for calls), reverse still works like factory etc.
    • Place the new daughterboard in the case and mount it using the 3 small black rivets provided, and reconnect the 3 factory ribbon cables to the new board Then, use the 3 piggyback cables from the daughterboard into the factory board on top (there are stand offs in the case to keep them apart. and remember to reconnect the antenna and rear cover fan wires. 1 screw to hold the motherboard in place. Before closing the case, make a hole in the sticker covering a hole in the case and run the cable for the android unit into the plug there. The video forgot this step, so did I, so will you probably. Then redo the 4 screws on back, 2 each top and bottom, 3 each side and put the 2 brackets back on.....all ready to go and not that tricky really.      
    • Onto the android unit. You need to remove the top screen because there is a daughterboard to put inside the case. Each side vent pops out from clips; start at the bottom and carefully remove upwards (use a trim remover tool to avoid breaking anything). Then the lower screen and controls come out, 4 screws, a couple of clips (including 3 flimsy ones at the top) and 3 plugs on the rear. Then the upper screen, 4 screws and a bunch of plugs and she is out. From there, remove the mounting brackets (2 screws each), 4 screws on the rear, 2 screws top and bottom and 3 screws holding in the small plates on each side. When you remove the back cover (tight fit), watch out for the power cable for the fan, I removed it so I could put the back aside. The mainboard is held in by 1 screw in the middle, 1 aerial at the top and 3 ribbon cables. If you've ever done any laptop stuff the ribbon cables are OK to work with, just pop up the retainer and they slide out. If you are not familiar just grab a 12 year old from an iphone factory, they will know how it works The case should now look like this:
    • Switching the console was tricky. First there were 6 screws to remove, and also the little adapter loom and its screws had to come out. Also don't forget to remove the 2 screws holding the central locking receiver. Then there are 4 clips on either side....these were very tight in this case and needed careful persuading with a long flat screw driver....some force required but not enough to break them...this was probably the fiddliest part of the whole job. In my case I needed both the wiring loom and the central locking receiver module to swap across to the new one. That was it for the console, so "assembly is the reverse of disassembly"
×
×
  • Create New...