Jump to content
SAU Community

noisy short shifter normal??

(B1) MR_fanny
 Share

Recommended Posts

(B1) MR_fanny Grand Master

(B1) MR_fanny

Posted
Posted

hey guys, i just installed a C's copy short shifter in my 33. installation was easy thanks to pranks DIY and it feels great, very solid and short. but its damn noisy as in i can actually hear the gearbox whine through the gears over the exhaust note. no noise prior to installation 2hrs before. just want to know if this is normal for a short shifter because of the way that its fixed onto the gearbox thru the base plate and clamps and that it transfers the noise of the gearbox thru the shifter itself. is this normal?? if not how can i reduce the noise?? my skyline sounds like my dads old crappy datsun:D:D

Link to comment
https://www.sau.com.au/forums/topic/55557-noisy-short-shifter-normal/
Share on other sites
rs73 Grand Master

rs73

Posted
Posted

It made an awful lot of noise on my car when I put one in, it was really loud and horrid. Ended up taking it out and sell it within a week. That was C's.

Not sure about Nismo short shifter, has anyone tried it? Perhaps Nismo one might be quieter?

(B1) MR_fanny Grand Master

(B1) MR_fanny

Posted
  • Author
Posted
probably due to the fact that the new shifter is a solid core, where as the original r33 one has a rubber-filled core to reduce stiffness and noise transfer... this is normal

that makes alot of sense, i can even hear the starter motor turning over chrisply thru the shifter itself..its bizzare. glad to hear that this sound is normal though it is slowly driving me nuts:D:D

~Hypnotik~ Rising Star

~Hypnotik~

Posted
Posted
It made an awful lot of noise on my car when I put one in, it was really loud and horrid. Ended up taking it out and sell it within a week. That was C's.

Not sure about Nismo short shifter, has anyone tried it? Perhaps Nismo one might be quieter?

I'm not sure about the Skyline Nismo shifter, but I know that the Nismo S13 Silvia/180sx shifter is no where near as short as the C's S13 shifter. The extra noise is the same with the S13 C's shifter so I've been told.

silva33 Mentor

silva33

Posted
Posted

i have no idea what is making the noise, the top clamp is very tight... now that u mention it i might see if there is a gap between the spacer and the top plate / clamp..?

does the fact that it is solid have anything to do with it?

does it matter if the 'wave' washer is under the spacer rather than over it? its difficult to fix as i have no idea what is actually the casue..

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now
 Share
Go to topic listing


  • Similar Content

  • Latest Posts

    • Dose Pipe Sutututu
      Duncan's V37.......race car?

      By Dose Pipe Sutututu · Posted

      Fark what are the changes of that snapping like that, clean. Nek minnit, custom radiator goes in, with built in oil cooler like those discontinued PWR ones from yesterdeacades ago
    • Duncan
      7 Speed Auto transmission fluid change (Skyline, Q50, Q60, Fuga, Q70, A62 Titan and probably heaps of others including Navara...)

      By Duncan · Posted

      I thought I'd do a write up on an auto transmission fluid change for a the nissan 7 speed Automatic. At some stage the genius engineers decided that the fluid in the trans was "for the life of the transmission", (which seems kind of self supporting to me) and removed the dip stick and fill tube (funnily enough there is still a casting for it). Anyway, for this job you do need 2 specialist tools in addition to regular hand tools, jack and good chassis stands. You need a way to pump fluid up to the transmission; I got one of these but there are plenty of other options: https://www.ebay.com.au/itm/364584087070 Don't trust the generic listing though, it does not come with the required adapter for the Nissan 7 Speed. You need one of these, can't do the job without it: https://navarapart.com.au/product/genuine-nissan-patrol-y62-d23-np300-navara-re7-dipstick-fill-connector1 You need a heap of compatible transmission oil. Could be Nissan, could be anything else rated for Nissan Matic S. You need at least 10 litres, I had 15 to give it a better flush... Also, you need some biiig oil catch trays, at least one of these, or bigger if possible (volume was fine, size was very marginal): https://autobarn.com.au/ab/Autobarn-Category/Tools-%26-Garage/Specialty-Tools/Oil-Service/Garage-Tough-Oil-Drain-Pan-Black-16L---GT1068/p/TO03191 Finally, a measuring jug is very useful if your pump does not have volumes marked on it, I got a 6l one: https://www.repco.com.au/oils-fluids/fluid-accessories/measuring-jugs/penrite-measuring-jug-6l-pmj006/p/A5322648 Oh, and gloves.....this stuff is horrible (not as bad as diff oil, but getting there) ....First, jack up your car.....
    • Duncan
      Duncan's V37.......race car?

      By Duncan · Posted

      So I mentioned the apprentice, @LachyK helped take the bonnet off. We just undid the nuts on the hinges and unclipped the gas struts, then pulled the bonnet back a little as the front was catching on the front bar.  I had a good look at everything today and have removed the rams, repaired/reset the hinges and bolted it back together like it never happened. I'll do a separate write up on the repair, and I also removed the poppers from the Fuga today too to save grief down the road.....as said above it is at least $5k to repair retail. I'm also happier about my ability to prepare a race car, and less happy about Nis-nault's engineering (I can hear @GTSBoy sAfrican Americaning) because the top hose of the radiator didn't slip off.......it snapped clean off. By practice I put the hose clamp hard up against the flare on a neck to make it least likely to ever move (thanks @Neil!). I guess that puts a little more pressure on the end of the pipe as it is further away from the rad, but still, that is pretty shit. I've put it back on for now as there was a fair bit of neck still there, but obviously there is no lip on the neck any more so I don't think I'll track it again until I have a new rad. Speaking of which....more research required. It looks like Koyo makes a standard size radiator in ally which I'll grab in the meantime, but I really want something thicker so might have to go custom in the medium term (ouch) Coolant still needs a refill and I have the pressure tester on it over night, but other than a wash down of the engine bay it seems alright. And @MBS206 noted something noisy on the front of the engine and I think I agree....time for a new accessory belt and tensioners I think.
    • Duncan
      Duncan's V37.......race car?

      By Duncan · Posted

      our good friends at nismo make a diff for it, I have one (and a spare housing to put the centre in) on the way. https://www.nismo.co.jp/products/web_catalogue/lsd/mechanical_lsd_v37.html AMS also make a helical one, but I prefer mechanical for track use in 2wd (I do run a quaife in the front, but not rear of the R32)
    • GTSBoy
      R33 persistent issues. P/steering and lag/misfire

      By GTSBoy · Posted

      What are we supposed to be seeing in the photo of the steering angle sensor? The outer housing doesn't turn, right? All the action is on the inside. The real test here is whether or not your car has had the steering put back together by a butcher. When the steering is centred (and we're not caring about the wheel too much here, we're talking about the front wheels, parallel, facing front) then you should have an absolutely even number of turns from centre to left lock and centre to right lock. If there is any difference at all then perhaps the thing has been put back together wrongly, either the steering wheel put on one spline (or more!) off, and the alignment bodged to straighteb the wheel, or the opposite where something silly was done underneath and the wheel put back on crooked to compensate. Nut there isn't actually much evidence that you have such a problem anyway. It is something you can easily measure and test for to find out though. My money is still on the HICAS CU not driving the PS solenoid with the proper PWM signal required to lighten the load at lower speed. If it were me, I would be putting either a multimeter or oscilloscope onto the solenoid terminals and taking it for a drive, looking for the voltage to change. The PWM signal is 0v, 12V, 0V, 12v with ...obviously...modulated pulse width. You should see that as an average voltage somewhere between 0V and 12V, and it should vary with speed. An handheld oscilloscope would be the better tool for this, because they are definitely good enough but there's no telling if any cheap shit multimeter that people have lying around are good enough. You can also directly interfere with the solenoid. If you wire up a little voltage divider with variable resistor on it, and hook the PS solenoid direct to 12V through that, you can manually adjust the voltage to the solenoid and you should be able to make it go ligheter and heavier. If you cannot, then the problem is either the solenoid itself dead, or your description of the steering being "tight" (which I have just been assuming you mean "heavy") could be that you have a mechanical problem in the steering and there is heaps of resistance to movement.
×
×
  • Create New...