Jump to content
SAU Community

Where's the taco sender?

Steg33

By Steg33,
in Engines & Forced Induction

 Share

Recommended Posts

Steg33 Community Regular

Steg33

Posted
Posted

My tacho has decided to play around (flickering) and then die on me. Funny thing is, once in a while on a hot day it works again. I've had the instrument cluster out and the wires seem to be fine between there and the ECU. I'm thinking it's the sender for the taco but not real sure where it is? can anyone tell me where this is or any other ideas what this problem could be?

It's on an R33 GTS-T and starting to sh1t me because i don't want to be bouncing it off the rev limiter just to find out when my revs are up.

I did a quick search and this dude had the same problem but to no avail:

http://www.skylinesaustralia.com/forums/sh...&highlight=taco

Any help would be appreciated guys.

Thanks :)

Link to comment
https://www.sau.com.au/forums/topic/55682-wheres-the-taco-sender/
Share on other sites
Guilt-Toy Grand Master

Guilt-Toy

Posted
Posted

I have this problem tooo!!! My tacho likes to sit at 8000rpm even at idle!! every now and then it will change to another setting like 3000rpm or 1200rpm... Sometimes you can catch it moving slowly others it goes instantly fast...

Steg33 Community Regular

Steg33

Posted
  • Author
Posted

The rest of the car runs fine so i guess it should only be a problem with the cluster because if the 'sender' from the motor was screwed then the ECU would have troubles aswell wouldn't it? should be able to get hold of a hand controller fairly soon for the power FC and narrow it down to the cluster if i get a correct reading from the ECU.

blind_elk Grand Master

blind_elk

Posted
Posted
yeah.. indeed it is.. but where is the ECU getting that reading? Its obviously somewhere off the engine loom.  

That is the important question..

The ECU is controlling the coilpacks, and it knows how many times it is telling the coils to fire in any given period of time.

It's pin 7 on the ECU.

Steg33 Community Regular

Steg33

Posted
  • Author
Posted
The ECU is controlling the coilpacks, and it knows how many times it is telling the coils to fire in any given period of time.

It's pin 7 on the ECU.

That's more what i was looking for.

Thanks heaps buddy.

Revhead Grand Master

Revhead

Posted
Posted

I had exactly the same problem. The tacho output was fried on the stock ECU, which apparently is not that uncommon on the R33. I replaced the ECU and the tacho instantly worked again.

I may be wrong, but I think the ECU works out engine RPM based on the CAS. From there, the ECU fires coils/injectors, and runs the tacho.

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now
 Share
Go to topic listing


  • Similar Content

  • Latest Posts

    • Erelyes
      Ceramic turbine damage to engine - what did yours do?

      By Erelyes · Posted

      Ha, well, it's been.... a bit of a journey. Things have taken much longer than I'd hoped. I'll probably put up a thread at some stage. Hopefully soon. The car's not done any kms since my update in June though, put it that way.
    • Dose Pipe Sutututu
      M35 Aftermarket Fuel Pump

      By Dose Pipe Sutututu · Posted

      Here's the chart for fuel pressure vs. current draw, assuming your base fuel pressure is 3 bar and you run like 0.5bar boost on WOT, you should only momentarily hit 9amps here and there. (Ignore my prev post, I cannot read a chart these days it seems)
    • GTSBoy
      RB25 Drama's

      By GTSBoy · Posted

      Those comp test results are not hideous. Whether they are accurate or not (ie, when that comp tester says 140 psi, is the real pressure120, 140 or 160?) is unknown to us. The state of the battery used to crank it over is unknown, etc etc. Many people around here would say that the absolute values and the spread are perfectly fine to just add boost and keep going. I personally would be happier with a narrower spread than that, but even the diff between 125 and 145 is not terrible. That one cylinder at 125 though, has probably copped some damage relative to the others. You should inspect the valves seeing as you've got it open. Do you know how to measure installed ring gaps? That, and an inspection of the rings themselves, is how you will determine whether they need to be replaced. If you're not good to do these things, take the block and the pistons and rings to a shop that is, and ask them for the go/no-go on them. Do the bores need a hone at all? If so, you might well be justified in getting some different pistons in order to get away from the ring supply problem. Whether you're happy to spend a lot more money right now, on more gear, rather than less money, but an amount that looks stupid given that you will only get a handful of rings in exchange for that money, is for you to decide.
    • iain_ST44GA
      M35 Aftermarket Fuel Pump

      By iain_ST44GA · Posted

      also possibly backed up to my filler and shat down it! 🤣
    • Julsmadrid
      RB25 Drama's

      By Julsmadrid · Posted

      Ok so i would love some advice here please, i purchased an R33 a few months back and its had a few mods done to the engine, its an RB25det running a Master ECU, 1200cc injectors, bigger turbo, oil cooler, oil filter relocation kit, Spool H-beam rods, acl/ross pistons. When i removed the motor from the vehicle (as its getting a respray) i thought i would compression test it and these are the following results. Cylinder 1-145psi, Cylinder 2-143psi, Cylinder 3-125psi, Cylinder 4-145psi, Cylinder 5-140psi, Cylinder 6-135psi this test was done with the motor on the ground and powering up the starter motor. I dropped the sump and found broken oil squirters on cylinder 3,5 and 6. I was told my rings are probably worn so i stripped the motor completely to get a new set of rings for it. The trouble is no one has these rings anywhere and they have to be custom made by Ross over in the states and will cost about $600+$200 delivery. My question is how can i tell if my rings are at fault and if they are still ok and is this price ok for a set of rings?
×
×
  • Create New...