Jump to content
SAU Community

Where's the taco sender?

Steg33

By Steg33,
in Engines & Forced Induction

 Share

Recommended Posts

Steg33 Community Regular

Steg33

Posted
Posted

My tacho has decided to play around (flickering) and then die on me. Funny thing is, once in a while on a hot day it works again. I've had the instrument cluster out and the wires seem to be fine between there and the ECU. I'm thinking it's the sender for the taco but not real sure where it is? can anyone tell me where this is or any other ideas what this problem could be?

It's on an R33 GTS-T and starting to sh1t me because i don't want to be bouncing it off the rev limiter just to find out when my revs are up.

I did a quick search and this dude had the same problem but to no avail:

http://www.skylinesaustralia.com/forums/sh...&highlight=taco

Any help would be appreciated guys.

Thanks :)

Link to comment
https://www.sau.com.au/forums/topic/55682-wheres-the-taco-sender/
Share on other sites
Guilt-Toy Grand Master

Guilt-Toy

Posted
Posted

I have this problem tooo!!! My tacho likes to sit at 8000rpm even at idle!! every now and then it will change to another setting like 3000rpm or 1200rpm... Sometimes you can catch it moving slowly others it goes instantly fast...

Steg33 Community Regular

Steg33

Posted
  • Author
Posted

The rest of the car runs fine so i guess it should only be a problem with the cluster because if the 'sender' from the motor was screwed then the ECU would have troubles aswell wouldn't it? should be able to get hold of a hand controller fairly soon for the power FC and narrow it down to the cluster if i get a correct reading from the ECU.

blind_elk Grand Master

blind_elk

Posted
Posted
yeah.. indeed it is.. but where is the ECU getting that reading? Its obviously somewhere off the engine loom.  

That is the important question..

The ECU is controlling the coilpacks, and it knows how many times it is telling the coils to fire in any given period of time.

It's pin 7 on the ECU.

Steg33 Community Regular

Steg33

Posted
  • Author
Posted
The ECU is controlling the coilpacks, and it knows how many times it is telling the coils to fire in any given period of time.

It's pin 7 on the ECU.

That's more what i was looking for.

Thanks heaps buddy.

Revhead Grand Master

Revhead

Posted
Posted

I had exactly the same problem. The tacho output was fried on the stock ECU, which apparently is not that uncommon on the R33. I replaced the ECU and the tacho instantly worked again.

I may be wrong, but I think the ECU works out engine RPM based on the CAS. From there, the ECU fires coils/injectors, and runs the tacho.

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now
 Share
Go to topic listing


  • Similar Content

  • Latest Posts

    • The king 2.0
      Nissan fuga 450gt android screen

      By The king 2.0 · Posted

      Hi guys . Can someone help me  I bought an Android screen for my Nissan fuga but it won't turn on   
    • MBS206
      NC MX5

      By MBS206 · Posted

      My guesstimate, with no real numbers to back it up, is it won't effect it greatly at all.its not a huge change in position, and I can't see the air flow changing from in turbulence that much based on distance, and what's in front of it. Johnny and Brad may have some more numbers to share from experience though.
    • dbm7
      Automatic Power Button Light Flashing

      By dbm7 · Posted

      Which solenoid? Why was it changed? Again, why was this done? ...well, these wear..but ultimately, why was it changed? Did you reset the idle voltage level after fitment? I'm just a tad confused ~ the flash code doesn't allude to these items being faulty, so in my mind the only reason to change these things, would be some drive-ability issue....and if that's the case, what was the problem? Those questions aside, check if the dropping resistor is OK ...should be 11~14 ohms (TCU doesn't throw a flash code for this) ~ also, these TCU designs have full time power (to keep fault code RAM alive), and I think that'll throw a logic code (as opposed to the 10 hardware codes), if that power is missing (or the ram has gone bad in the TCU, which you can check..but that's another story here perhaps).
    • The Bogan
      NC MX5

      By The Bogan · Posted

      Question for people who "know stuff" I am looking at doing the new intake like the one in the picture (the pictured is designed for the OEM TB and intake plenum), this design has the filter behind the front bar, but, the filter sits where the OEM duct heads into the front bar, and the standard aperture when the OEM ducting is removed allows the filter to pulled back out of the front bar into the engine bay for servicing, a simple blanking plate is used to seal the aperture behind the filter This will require a 45° silicone hose from the TB, like the alloy pipe that is currently there, to another 45° silicone hose to get a straight run to the aperture in the front bar Question: how will it effect the tune if I move the MAF about 100-150mm forward, the red is around where my MAF is currently, and the green would be where it would end up Like this This is the hole the filter goes through  Ends up like this LOL..Cheers    
    • Duncan
      R34 Plug Identification

      By Duncan · Posted

      Despite the level up question, actually I do know what that is....it is a pressure sender wire.  So check out around the oil filter for an oil pressure sender, or maybe fuel pressure near the filter or on the engine. Possibly but less likely coolant pressure sensor because they tend to be combined temp/pressure senders if you have one. Could also be brake pressure (in a brake line somewhere pre ABS) but maybe I'm the only one that has that on a skyline.
×
×
  • Create New...