Jump to content
SAU Community

FS Hr31 passage gt 1989 Series 2

hot20t

By hot20t,
in For Sale (Private Whole cars only)

 Share

Recommended Posts

hot20t Apprentice

hot20t

Posted
Posted

1989 Hr31 passage gt

plates:OMY31T

ok this thing is rare for those who dont know what it is...its a 4dr pillarless r31 skyline jap import with ECCS red rocker cover RB20DET..power windows/mirrors electronic adjustable dampers in the shocks(hard,medium,soft) HICAS steering 4WAS(ABS) IRS,Climate Control(aircon needs re-gas though) Automatic...electric bucketing/lumbar support in driver seat, Blackwidow alarm system....pretty much an r32 in an r31 shell...its 89 model the last of the r31's..

MODS

Turbosmart in cabin gated boost controler

comes with a set of chrome 17" GZero's and a set of jap silk 15"rims(silver)

exhaust:dragpipe from turbo(no dump pipe)into 3" mandrel bent stainless steel with high performance high flow drift cat from japan and a DRFT stainless/titanium tip muffler

VG20 ballbearing turbo have had this thing out to 1.6 bar about 22psi

VR4 frount mount(has been piped up temp...for dyno test needs to have proper piping done)

Pod Filter

Lowered

Apexi fuel/revlimit defender

Auto gearbox has shift kit and high pressure oil pump also can switch between power/normal/hold gear modes on it

Original GTSR Impul Racing Development 260km/h speedo

the car will come with a heap of spares including an almost complete rb20det which came out of a car that made 165rwkw on the dyno,the motor will need a new oil pump,timing belt tensioner gear,a piston lol, and a new set of valves...the head is fully ported...i suggest gettin new valves and putting it on the engine thats in the car, comes with 4 spare doors with windows and all working internal electronic mechanisms,spare boot,spare dash...heaps more stuff i have here for it which you will find hard to get.

it HAD a full system in it but it was taken out and swapped for an rx7

Genuine offers over $9,000

should be running mid to hi 13's on 15psi

IMG: http://groups.msn.com/Rareskylines/shoebox...Photo&PhotoID=1

Link to comment
https://www.sau.com.au/forums/topic/55705-fs-hr31-passage-gt-1989-series-2/
Share on other sites

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now
 Share
Go to topic listing


  • Similar Content

  • Latest Posts

    • Dose Pipe Sutututu
      What should I do next to hold the head on

      By Dose Pipe Sutututu · Posted

      Possibly avoid using a Cometic one unless the deck/head surface are perfectly flat. I did have a look just then and forgiving gaskets such as Tomei or Nitto don't exist for the FJ20, however the Bar-Tek or Kameari ones look good and might do the trick.
    • GTSBoy
      boost source Size Garrett gt28 gen2

      By GTSBoy · Posted

      Because pipe threads for pipe things. M threads for bolt things. Throw some teflon sealant onto it and dust your hands off knowing you did the right thing, instead of going twice around the block to achieve a result using the wrong things. Of course, all of these solutions are ignoring the fact that the minimum thread pitch we're talking about here is 1.25mm, with the 1/4" in NPT or BPS being out around 1.4mm. You will need to know that the boss you're tapping has enough thickness for at least a few threads. That's one of the reasons that 1/8" is commonly used - because the pitch is <1mm. And why would you look to use 1/4" NPT in a BSP country anyway? Ugh.
    • Dose Pipe Sutututu
      boost source Size Garrett gt28 gen2

      By Dose Pipe Sutututu · Posted

      Just throwing around ideas, does it need to be in the compressor cover? Why not the hot side piping?
    • timmy94
      boost source Size Garrett gt28 gen2

      By timmy94 · Posted

      1/8NPT drill size = 8.7mm. Since the hole got messed up by me, it’s probably around 9mm.    So 1/4” NPT would be next step. A drill size of around 11mm would be preferred there which is not way of my M12 (drill 10.5mm and tap M12 threads) 
    • oHBoy.
      2001 R34DE

      By oHBoy. · Posted

      3 Kids are starting to hit that ages. I wanted to get them something special to learn on, put down the screens and have some fun. 4Door 2001 R34DE Black Pearl GV1 Jap Import, AU 2nd owner. Pre Work done. Suspension - Wheels Pedders SportsRyder Coilovers   Wheels TSG Spokey Boi 18'x9.5"+15 Body JASI Aero 4 door Type R Full Kit LED Conversion - Parker, Blinkers, & Reverse Exhaust Hurricane Headers 100 CPI high flow cat 2.5" Piping Cannon muffler Internal Bride low max stradia ii - front seats  Bride RO seat base and Rails (R/H) Cube short shifter LED Conversion - Interior   
×
×
  • Create New...