Jump to content
SAU Community

place to rebuild tein suspension in Vic?


Recommended Posts

Hey all,

I'm pretty sure my rear passenger side tein shock has stuffed up; the car now slightly leans to the side where i think the fkt shocker is, and the other rear side is higher than it was before. Anyone got any idea how much it will cost to repair or know anywhere that can do it?

Cheers!

Apparently they send it to Japan... but try

ACCESS PERFORMANCE DISTRIBUTORS

9 TRADE PLACE VERMONT

VICTORIA 3133

AUSTRALIA

TEL: (03) 9873 0133

FAX: (03) 9873 1311

EMAIL: [email protected]

[email protected]

bah.. why send to japan when you can send to sunny QLD.. your TEINS would love a holiday up here :P

As far as I know these people are the only people in the country that specialise in this..

www.shockreco.com.au

I think you'll pay around $200 per corner.

Apparently they send it to Japan... but try

ACCESS PERFORMANCE DISTRIBUTORS

9 TRADE PLACE VERMONT

VICTORIA 3133

AUSTRALIA

TEL: (03) 9873 0133

FAX: (03) 9873 1311

EMAIL: [email protected]

[email protected]

i have spoken to these guys sometime ago and they said its cheaper to buy a new coilover than sending it to japan.

as far as i know only the QLD place predator advised does them...but i may be wrong.

predator, excellent. Thanks for the info. They can fix and return shocks in about a week. it will cost $137.50 per shock, and depending on the damage on them, like if the shaft is rooted, can cost up to $300 each to fix. I'll have to send em up and see how it goes.

thanks guys!

  • 5 months later...

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now


  • Similar Content

  • Latest Posts

    • There's restrictor pills in the stock boost control hoses. That's how they set the amount that was bled off and hence the "high" boost setting. The usual mod in the day was to remove it and send the "high" boost setting up to about 14 psi.
    • Thanks Duncan, that's the best info I've read. Furthermore after learning about the PCM programming side controlling the factory boost solenoid, the purpose of the solenoid is to "bleed" boost when pin 25 is earthed, thus allowing spring pressure in the wastegate actuator to overcome diaphragm boost pressure, thus closing or reducing the position of the wastegate flap creating more boost as the turbo is able to spin faster. It's pretty cool to see a designated Pill to do exactly this, would have liked to have seen it with a tiny filter over the end for those moments in vacuum.  The constant bleed pill has now been removed completely from the system and solenoid boost control has been restored once again.   Case closed 😂
    • The wideband reading is meaningless if it's not running. Why are you using shitty old sidefeeds on any engine, let alone a Neo? What manifold and fuel rail are you using to achieve that? Beyond that, can't help you with AEM stuff as I've never been their ECU/CAS combo.
    • Manual boost controllers (where a little of the boost was bled off) were quite common back in the day, because they were cheap and easy. Generally they had a manual adjustment screw rather than being fixed like yours. Down side is they always bleed boost, not just when you want them to so an electronic boost controller that uses a solenoid will have less lag.
    • Hello , im new here and i have A31 home build  RB25det neo stock eng / turbo  aem ems 2 blue connector  aem 3.5 map aem cas disk aem wideband connected to ecu  355 lph pump 550 nismo yellow injectors side feed aftermarket regulator  and won’t start with base aem tuner basic tune eventually flipped cas 180 degree so it triggers on correct stroke not in exhaust cycle  Now it won’t start Wideband reads 10 and 11 at lowest fuel setting  and will share calibrations soon for aem tuner i think something is wrong in aem tuner    please if you have any information, am very grateful         
×
×
  • Create New...