Jump to content
SAU Community

CHEAP!!!! R32 GTR '89 - 56,000km - $22,500

rx-[7]

By rx-[7],
in For Sale (Private Whole cars only)

 Share

Recommended Posts

rx-[7] Community Regular

rx-[7]

Posted
Posted

CHEAP!!!! R32 GTR '89 - 56,000km - $21,500

Got a DEAD stock R32 GTR for sale

*DEC 1989 build (one of very few in australia, for the time being)

*56,000km on the clock (cant prove its right, but it looks like the car has very low km)

*Gunmetal grey

*Had engine rebuild in japan 11,000 km ago (why i dont know but it has!)

*Just freshened up the breaks (machine, and bendix ultamate pads all round)

*Just rebuilt clutch master cylinder and booster

*Just changed all fluids and filters top to bottom

*Rego for 10 months

*Everything works (excpt no a/c gas as it was degassed in japan, but ac does work)

*NO MODS!!!!!!

*Top of the range alarm with 3 point immobilizer just installed (works GREAT!)

Pics at http://chubby.nameserve.org/~mypics/gtr/

only probs with the car are:

*slight exhaust leak, Pretty sure its the gasket from the cat to the rear section of the exhaust

*wear on the drivers seat (very common)

*dint on left front guard can see in the 2nd pic, but only notice it if your looking for it.

Very nice clean car

$21,500

Sydney 0410496449 Jacob

Reason for sale, lost my licence can show paper work

Link to comment
https://www.sau.com.au/forums/topic/56788-cheap-r32-gtr-89-56000km-22500/
Share on other sites
rx-[7] Community Regular

rx-[7]

Posted
  • Author
Posted

i dont like to make people read "bump" for half a page.

For anyone who is interested in reading the other thread the address is http://www.skylinesaustralia.com/forums/sh...ead.php?t=53907

Some questions and lots of "bumps"

Count Grantleyish Grand Master

Count Grantleyish

Posted
Posted

Hey,

Is it privately imported or you are the second owner in Oz?

Might be interested but not for couple of months...

Cheers

Grant

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now
 Share
Go to topic listing


  • Similar Content

  • Latest Posts

    • Duncan
      Mistakes were made, my R34 Story

      By Duncan · Posted

      Have a look at that (shitty) pic I posted. You can see AN -4 braided line coming to a -4 to 1/8 BSPT adapter, into a 1/8 BSPT T piece. The Haltech pressure sender is screwed into the long arm of the sender and factory sender (pre your pic) into the T side. You can also see the cable tie holding the whole contraption in place. Is it better than mounting the sender direct to your engine fitting......yes because it removes that vibration as the engine revs out 50 times every lap and that factory sender is pretty big. Is it necessary for you......well I've got no idea, I just don't like something important failing twice so over-engineer it to the moon!
    • GTSBoy
      Mistakes were made, my R34 Story

      By GTSBoy · Posted

      Yup. You can get creative and make a sort of "bracket" with cable ties. Put 2 around the sender with a third passing underneath them strapped down against the sender. Then that third one is able to be passed through some hole at right angles to the orientation of the sender. Or some variation on the theme. Yes.... ummm, with caveats? I mean, the sender is BSP and you would likely have AN stuff on the hose, so yes, there would be the adapter you mention. But the block end will either be 1/8 NPT if that thread is still OK in there, or you can drill and tap it out to 1/4 BSP or NPT and use appropriate adapter there. As it stands, your mention of 1/8 BSPT male seems... wrong for the 1/8 NPT female it has to go into. The hose will be better, because even with the bush, the mass of the sender will be "hanging" off a hard threaded connection and will add some stress/strain to that. It might fail in the future. The hose eliminates almost all such risk - but adds in several more threaded connections to leak from! It really should be tapered, but it looks very long in that photo with no taper visible. If you have it in hand you should be able to see if it tapered or not. There technically is no possibility of a mechanical seal with a parallel male in a parallel female, so it is hard to believe that it is parallel male, but weirder things have happened. Maybe it's meant to seat on some surface when screwed in on the original installation? Anyway, at that thread size, parallel in parallel, with tape and goop, will seal just fine.
    • Kinkstaah
      Mistakes were made, my R34 Story

      By Kinkstaah · Posted

      How do you propose I cable tie this: To something securely? Is it really just a case of finding a couple of holes and ziptying it there so it never goes flying or starts dangling around, more or less? Then run a 1/8 BSP Female to [hose adapter of choice?/AN?] and then the opposing fitting at the bush-into-oil-block end? being the hose-into-realistically likely a 1/8 BSPT male) Is this going to provide any real benefit over using a stainless/steel 1/4 to 1/8 BSPT reducing bush? I am making the assumption the OEM sender is BSPT not BSPP/BSP
    • funkymonkey
      Jacks that fit under GTR lips that can reach the subframe?

      By funkymonkey · Posted

      I fashioned a ramp out of a couple of pieces of 140x35 lumber, to get the bumper up slightly, and then one of these is what I use
    • GTSBoy
      Mistakes were made, my R34 Story

      By GTSBoy · Posted

      I wouldn't worry about dissimilar metal corrosion, should you just buy/make a steel replacement. There will be thread tape and sealant compound between the metals. The few little spots where they touch each other will be deep inside the joint, unable to get wet. And the alloy block is much much larger than a small steel fitting, so there is plenty of "sacrificial" capacity there. Any bush you put in there will be dissimilar anyway. Either steel or brass. Maybe stainless. All of them are different to the other parts in the chain. But what I said above still applies.
×
×
  • Create New...