Jump to content
SAU Community

rb30det bearings turbo or non turbo??

Wrath

By Wrath,
in Engines & Forced Induction

 Share

Recommended Posts

Wrath Contributor

Wrath

Posted
Posted

Hi guys

im building a Rb30Det and i have just got my bottem end parts back from the machine shop... im about to order some ACL race bearings and i was wondering is there any difference between the turbo and non-turbo main bearings...

which should i use.

Link to comment
https://www.sau.com.au/forums/topic/57427-rb30det-bearings-turbo-or-non-turbo/
Share on other sites
Guilt-Toy Grand Master

Guilt-Toy

Posted
Posted

hey dude

ive used stocko first size over sized ACL bearings and ive had no issues so far... 8000km later and 230rwkw from rb30det and no issues at all.

If you want more then 300rwkw i would suggest something more appropriate but 300rwkw is pretty hard anyway.

good luck

proengines Rising Star

proengines

Posted
Posted

The ACL race series bearings are a nice thing, good material, hard back etc.. the only thing I would modify is to drill the extra feed holes through the oil groove in the upper bearing in the same way the original Nissan bearings are done. ACL will be doing this in the future on these bearings according to their rep I was speaking to a week or so ago.

The other bearings I have found good are King, especially for conrod bearings. They run a very hard backing and a single layer of alecular bearing material rather than separate layers with an overlay that can flake under high loads/heat.

Genuine Nissan conrod bearings don't seem to cope terribly well with any detonation. We recently had the sump off a 26 running around the 300rwkw mark and the Nissan conrod bearings had started to delaminate and had lost their tension. They wouldn't clip back into the rod, I've still got them here if you'd like a photo. We replaced them with King bearings. I haven't tried the Nismo bearings in the same situation but apparently they are a lot better than standard Nissan.

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now
 Share
Go to topic listing


  • Similar Content

  • Latest Posts

    • The Bogan
      NC MX5

      By The Bogan · Posted

      After using a protractor for an actually accurate assessment of what is required,  and by NOT using my uncalibrated eyeball I worked out I need a 25° silicone bend from the TB ro the MAF, but, my choice was either a 30° or a 23° (23° is a weird spec), so I grabbed the 23° one from Raceworks I also grabbed 1mtr of 3" straight from Just Jap, I needed 350mm, but they only had 300mm, or 1mtr lengths....meh Also ordered a 1/2" hose bulkhead fitting from fleabay, this has a smoothish mushroom looking head (they are designed for below the water line of boats) that will fit inside the bend, the hose bit and threaded bit looks to long, but nothing that a hacksaw cannot fix if required, the hose will then just get jamed on the threaded bit up to the retaining nut Fingers crossed and the unsightly amount of hose clamps will be reduced down to 4 once all the parts arrive 
    • joshuaho96
      R34 25GT Engine Light 21

      By joshuaho96 · Posted

      Oil change does not trigger code 21. Code 21 is for coilpacks primary side connection. You can try to clear the code with a battery disconnect, hold down the brake pedal to drain capacitors through the brake lights with the ignition on for 10-15 seconds before you reconnect the battery. I have seen R35 coil conversion permanently cause this code with no ill effects so it might be the resistance it wants to see isn't quite right on one or more coilpacks. Could be inside the ECU, could be the harness, could be a coil. You can test it all if you want or just ignore until the car actually starts misfiring.
    • joshuaho96
      R32 GTS (RB20DE) Injectors Replacement

      By joshuaho96 · Posted

      I forgot you have a Nistune ECU. Use Nistune to do all the tests I mentioned instead of faffing with 30+ year old electrical connectors. You can read MAF volts off that too, there are reference values in the service manual to tell you roughly what it should be in different conditions.
    • GTSBoy
      R32 GTS (RB20DE) Injectors Replacement

      By GTSBoy · Posted

      No. I think it might be the AFM. Hence the use of the terms "swaptronics", which implies the use of swapping out electronics for the purpose of diagnosis. It's about the only way to prove that a small/niggling/whatever problem with an AFM or a CAS or similar is actually caused by that AFM/CAS/whatever. A known good item swapped in that still gives the same problem is likely to be caused somewhere else. They're all the same. Spraying AFMs with cleaner is an each way bet between cleaning it and f**king it.
    • codygrimm27
      Can you mount the ATTESA pump in other locations?

      By codygrimm27 · Posted

      Oh wow! This might actually work amazingly. Do you know the ratio of the diff? I was told the only thing you need to make sure of is if the front & rear diff ratios are the same. Ours is a 4.083 Thanks!
×
×
  • Create New...